background image

Manual 2100-579A
Page 

1 of 41

FLF075V42A 

FLR075V42A FLR100V48A 

FLR100V60A FLR130V60A

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE 
VICINITY OF THIS OR ANY OTHER APPLIANCE.

IMPORTANT NOTICE

THIS FURNACE IS NOT INTENDED FOR USE AS A CONSTRUCTION HEATER. USE OF 
THIS FURNACE DURING CONSTRUCTION AND FINISHING PHASES OF A STRUCTURE 
IS CONSIDERED AS “OPERATION IN A CORROSIVE ATMOSPHERE” AND “UNUSUAL, 
NEGLIGENT OR IMPROPER USE” AND AS SUCH ARE CONSIDERED EXCLUSIONS BY THE 
BARD MANUFACTURING COMPANY LIMITED WARRANTY.

         

WARNING

CARBON MONOXIDE POISONING HAZARD

FAILURE TO FOLLOW THIS WARNING COULD RESULT IN PERSONAL INJURY OR DEATH.

Carbon Monoxide is invisible, orderless and toxic!  Bard Manufacturing recommends a carbon 
monoxide alarm in your home, even if you do not own a gas appliance.  Locate the carbon 
monoxide alarm in the living area of your home and away from doorways to attached garages.  
Follow the alarm manufacturer’s instructions included with the alarm.

         

WARNING

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION.

THIS INSTALLATION MUST COMPLY WITH THESE INSTRUCTIONS AND THE  REQUIREMENTS 
OF ALL GOVERNING CODES AND ORDINANCES FOR THE INSTALLATION LOCATION.

IT IS THE RESPONSIBILITY OF INSTALLER TO KNOW AND UNDERSTAND ALL OF THESE 
REQUIREMENTS.

FAILURE TO DO SO COULD CREATE A HAZARD RESULTING IN PROPERTY DAMAGE, BODILY 
INJURY OR DEATH.

OIL FURNACE 

INSTALLATION  INSTRUCTIONS

Manual: 2100-579A
Supersedes: 2100-579
File: 

VOL. I, TAB 3

Date: 04-24-13

Bard Manufacturing Company, Inc.
Bryan, Ohio  43506

Since 1914...Moving ahead just as planned.

MODELS

Summary of Contents for FLF075V42A










































Reviews: