Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
All the examples and pictures used here are for reference only. There may be several technically incorrect places
or printing errors in this manual. The updates will be added into the new version of this manual. The contents of
this manual are subject to change without notice.This device should be operated only from the type of power
source indicatedon the marking label. The voltage of the power must be verified before using the same.
Hybrid DVR
Quick Start Guide
This series of the product supports 1 SATA hard drive. Please make sure
that the device is powered off before the installation. The pictures of
the installation are only for reference, please take the real object as the
standard.
The interfaces of the rear panels are for reference only.
1. HDD Installation
2. Rear Panel Installation
• Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
• Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This will bring up
a shutdown window. The device will shut down by clicking “OK” button.
Then disconnect the power.
3. Startup & Shutdown
4. Login
First connect the camera to the DVR. Then go to Start
→
Settings
→
Camera
→
Manage Camera
→
Signal Access Set to checkmark
the video mode. The actual signals input shall correspond to the
video mode. Please refer to User Manual for details.
5. Analog Camera Connection
After you finish adding IP cameras, you can see the live images
through the monitor of the DVR. The following will mainly
introduce how to add the IP cameras via LAN/WAN.
6.
Network Configuration & Add IP Camera
• LAN
1.
Set the network of the DVR. Go to Start
→
Settings
→
Network
→
TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using
DHCP, please enable DHCP in both the DVR and the router.
2.
Go to Start
→
Settings
→
Network
→
Port. Input HTTP port
(the default value is 80), server port (the default port is 6036).
3.
Click “Apply” to save the settings.
4.
Go to Start
→
Settings
→
Camera
→
Add Camera. The DVR will
automatically refresh the cameras searched. The IPC which
supports the Onvif protocol may be added manually. If the IPC
searched is not in the same local network as the DVR, you should
select the device and click
to modify the IP address.
Rear Panel for 8CH
Rear Panel for 16CH
Rear Panel for 4CH
1.
Loosen the screws to open the
cover.
2.
Screw the screws into the HDD
but not tighten them.
3.
Place the HDD onto the bottom
of the machine.
4.
Connect the power and data
cables.
5.
Turn over the machine and secure
the HDD with the screws.
6.
Install back the cover and secure
it with the screws.
AUDIO
OUT ALARM OUT
CVBS
LAN USB DC12V RS485
VGA
B A
3 2
AUDIO IN
4
3
2
VIDEO IN
4
1
1
ALARM IN
4 3 2 1
C
O
M
G
N
D
N
O
LAN
USB DC12V
B
A
VGA
AUDIO
IN
9
VIDEO IN
8
7
16
15
4
3
12
11
2
1
10
6
5
14
13
AUDIO
OUT
RS485
Username
Password
admin
Login
Enter Password
Display Password
Log InAutomatically
Edit
S
ecurity
Q
uestion
Login
Cancel
Mac Address
IP Address
Edit IP
192
.
168
.
1 . 45
255
.
255
.
255 . 0
admin
192
.
168
.
1 . 1
Subnet Mask
Username
Gateway
Password
OK
Cancel
CE :98 :23 :75 :35 :22
4.0.0.1.beta1
Version
80
No.
IP Address
Edit
Port
Protocol
Model
Subnet Mask
1
192.168.2.45
XXX
XXX
255
.
255
.
255
.
0
Quickly Add
Manually Add
Add
Camera
Selected: 1/1
Add
Default Password
Remain Bandwidth: 10 / 10 Mb
Cancel
Port
TCP/IPv4
DDNS E-mail
NAT
IP Address Settings
Obtain an IP address automatically
Ethernet Port 1 ( Online )
Obatin DNS server address automatically
IP Address
Preferred DNS
192 . 168 . 1 . 2
0 . 0 . 0 . 0
192 . 168 . 1 . 1
192 . 168 . 1 . 1
0 . 0 . 0 . 0
Subnet Mask
Alternate DNS
Gateway
UPnP
Network Status
C V B S
Internet
DC 12V
U S B
L A N
V G A
B
A
A U DIO I N
4
3
2
1
V IDE O I N
8
4
2
1
7
3
6
5
A U DIO O U T
G
N
D
G
N
D
1
C
O
M
N
O
2
3
4
A L A R M O U T A L A R M I N
R S 485
For our T900 series DVRs, the
default username is admin
and the
default password is 123456
. When starting T900 series DVR for the
first time, you will see a prompt to begin a startup wizard. You can
skip this wizard if you would like, but it will help you configure basic
settings for your DVR. The wizard may allow you to also change the
default password for better security. If you decide to skip the wizard,
to access the live view and start using your DVR click on the Start
button in the bottom left of the menu bar on the bottom of the
screen and then click on Login and enter in the default password.
