AVO Turboworld's Bolt-on Instructions Manual Download

Page: 1 / 25

AVOTurboworld – For All Your Turbo Needs

Tel +61 3 95844699

Page 1 of 25

Fax +61 3 95844008

Created on 6/17/08 12:30 PM

www.avoturbo.com
[email protected]

AVOTurboworld Turbo system Fitting Instructions

for the 2001-2004 2.5-liter Subaru Impreza RS

Congratulations on purchasing AVO Turboworld

’

s Bolt-on Turbo Kit for the Subaru 2.5-liter RS. You are now

the proud owner of a turbosystem that draws on experience gained by not just 10 years of Subaru high
performance tuning, but more importantly 25 years of experience designing, manufacturing, installing and
modifying turbochargers.

Not only will this turbosystem greatly increase your engine

’

s power over stock, but it will also be user friendly

to drive and will remain so for many years of trouble free operation, with proper installation, servicing and
maintenance.

Contents

Chapter

Page

Orientation 2

Tools and Consumables Required 6

Pre-Installation Preparations 7

Disassembly 8

Turbo Oil Return System 9

Turbocharger Assembly 9-10

Turbocharger C Lubrication 11-12

Turbocharger Intake System 13-14

Mechanical Systems Check 16

Engine Management Installation 17+18+19

Turbosystem Testing 20

Operation and Maintenance 21

Summary of Contents for Turboworld's Bolt-on


























Search results

Summary of Contents for Turboworld's Bolt-on

Reviews:

Related manuals for Turboworld's Bolt-on

Brands by name

Popular brands

AVO Turboworld's Bolt-on, Instructions Manual

Search results

Summary of Contents for Turboworld's Bolt-on

Reviews:

Related manuals for Turboworld's Bolt-on

Brands by name

Popular brands