background image

OPERATION INSTRUCTIONS 

 
 
 
 
 

REMOTE CONTROL TRANSMITTER OPERATION 

 

Your Car-Pro Security System comes with two 3-button Remote Control 
Transmitters that feature a sophisticated code hopping system that will prevent 
illegal use of a code grabber with an attempt to record and steal your transmitter 
codes. 

 

LOCK – ARM & LOCK 

To arm your Security System, press the LOCK button once.  The siren will chirp 
(1) time and the vehicles parking lights will flash (1) time indicating that the 
Security System is now armed. The vehicles doors will lock upon arming when 
interfaced with the Security System. 

 

UNLOCK – DISARM & UNLOCK 

To disarm your Security System, press the UNLOCK button once. The siren will 
chirp (2) times and the vehicles parking lights will flash (2) times indicating that 
the Security System is now disarmed. The vehicles doors will unlock upon 
disarming when interfaced with the Security System.  

 

DELETING THE ARM/DISARM CHIRP

 

When attempting to arm or disarm your Security System, you have the option of 
temporarily muting the siren chirp sound. To perform this function, simply 
depress both LOCK & UNLOCK buttons on the Remote Control Transmitter at 
the same time. No chirp sound will be heard, arm / disarm confirmation will be 
through the vehicles parking lights only. 

 

VEHICLE LOCATOR 

Your Car Pro Vehicle Security System is equipped with a vehicle locator function 
which chirps the siren 6 times and flashes the vehicle’s parking lights 12 times to 
easily locate your vehicle. To access this function, simply press the “Trunk” and 
“Unlock” buttons at the same time. 

 

REMOTE PANIC FUNCTION 

The Remote Control Transmitter may be used as a remote panic switch that will 
activate the Security System’s siren and the vehicles parking lights in case of an 
emergency. To activate the PANIC function, press and hold the 

Lock 

button on 

the Remote Control Transmitter for (3) seconds.  The siren will sound and the 
vehicles parking lights will flash continuously. To cancel the PANIC function, 
press the lock or unlock button on the Remote Control Transmitter. 

 

TRUNK RELEASE FUNCTION / PAGER OUTPUT 

(OPTIONAL

You may use the Trunk button on your Remote Control Transmitter for a 
separate function. For example, if your vehicle is equipped with an electronic 
trunk release, the Security System can be interfaced with it and can electronically 
release your trunk by pressing the Trunk button for 2 seconds on the Remote 
Control Transmitter.  For additional security you have the option of this output 
programmed as vehicle security pager trigger output. Consult with your dealer! 

 

REMOTE CONTROL TRANSMITTER PROGRAMMING 

In the event, you should need to add or replace a Remote Control Transmitter, it 
is important that you follow the instructions below.  

 

Note: 

Each step must be performed within 10 seconds of the previous step 
otherwise the system will exit the programming mode.

 

 
 

 
 
 

1.    Enter: 
       a.   Turn the vehicles ignition to the “ON” position 
       b.   Push the valet switch 6 times. There will be 1 long chirp confirmation. 
       c.   You are now ready to program the Remote Control Transmitter(s). 
2.    Programming the Remote Control Transmitters: 

a.  Press any button on the first transmitter. There will be 1 short chirp. 
b.  Within 10 seconds push any button on the second transmitter.          

There will be two short chirps confirming

3.    Exit: 
       a.   Turn the vehicles ignition to the “OFF” position, Or 

b.   Leave for 10 seconds; there will be 3 long chirps to confirm exit. 

 

Note:

 

The Security System will only retain the last 4 Remote Control 
Transmitters programmed. If the Transmitter memory is exceeded, the 
Security System will start deleting Transmitters from memory in 
chronological order.  

 

CHANGING THE REMOTE CONTROL TRANSMITTER BATTERY 

The Remote Control Transmitters come with (1) miniature 12-volt battery. Under 
normal use this battery should have a life of approximately one year. If you 
should need to replace your battery you may want to return to your installing 
dealer. You may also wish to change the battery by yourself. When purchasing 
the battery be sure to purchase any of the following: GP23A, #EL12, #VR22 or 
Radio Shack #23-144. 

 

To replace the battery, carefully remove the case screw located on the bottom of 
the Remote Control Transmitter where the key ring attaches to the case. 

Use a 

miniature #1 Phillips head screwdriver! 

After removing the screw, carefully pop open the plastic case. Before removing 
the battery note the direction of its “+/-“ terminals. Install the new battery exactly 
the same way using caution not to bend the battery contacts. Replace the case 
cover and insert and tighten the screw. 

Do not over tighten! 

Test the Remote 

Control Transmitter. 

 

SYSTEM OPERATION 

 

OVERRIDE FUNCTION 

The OVERRIDE FUNCTION may be used if the Remote Control Transmitter is 
lost or inoperative.  To operate, enter the vehicle (alarm will sound), turn the 
vehicles ignition to the “ON” position and push the valet/override switch until the 
Security System stops sounding. The Security System is disarmed & reset. Have 
your Remote Control Transmitter serviced or replaced. 

 

VALET FUNCTION 

The Security System has a valet or stand-by mode that can be used when the 
vehicle is being serviced or valet parked. To activate the valet, turn the vehicles 
ignition to the “ON” position, then push and hold the valet / override switch for 2 
seconds or until the Security Systems LED turns ON solid. Turn the vehicles 
ignition to the “OFF” position; your vehicle is now in valet mode. To reactivate, 
repeat the above procedure noting the Security Systems LED will now turn OFF. 

 

Note: 

If your vehicle has the Keyless Entry option installed, you can still lock 
and unlock the vehicles doors with Remote Control Transmitter while in 
the Valet Mode.

 

 

PASSIVE/MANUAL OPERATION 

Manual Arming / Disarming is controlling your Security Sy stem via the Remote 
Control Transmitter.  This security system is equipped with an optional Passive  
 
Arming feature, which allows the Security System to arm 30 seconds after the 
last door is closed. Operation is as follows. 
 
1. 

Turn the vehicles ignition to the “OFF” position and exit the vehicle. 

2. 

After all entrances are closed, the Security Systems LED will flash fast for 
30 seconds. If you re-open any door, the Security Systems LED will stop 
flashing. It will begin flashing again once the vehicles door is c losed. 

3. 

After the 30 second timer has elapsed, the Security System will 
automatically “ARM”. The siren will chirp (1) time and the vehicles parking 
lights will flash (1) time. 

 

Note:  

If the vehicles door locks have been interfaced to the Security System, 
the vehicles doors will automatically lock after the passive arming cycle 
has been completed.  If this feature is not desired, see your local 
dealer and have the Security System re-programmed to eliminate 
passive door

 

locking. 

 

PASSIVE ARMING BYPASS 

Your Car-Pro Vehicle Security System can temporarily bypass the Passive 
Arming function via the Remote Control Transmitter for one arming cycle. To 
temporarily bypass Passive Arming, press the Trunk button twice before exiting 
the vehicle. The Security System will confirm with 1 short chirp. Passive 
operation will be restored once the Security System is armed by the Remote 
Control Transmitter.  

 

PRIORITY UNLOCK (

OPTIONAL

)

 

Your AutoPage Security System is equipped with a priority door unlock feature 
which will independently unlock the drivers door only when disarming the 
Security System. Pushing the Unlock button a second time within 3 seconds will 
unlock the entire vehicle. 

This feature requires additional installation and is not a 

standard feature of the Security System.

 

 

AUTOMATIC REARMING (

OPTIONAL

If this feature is selected, the Security System will automatically re-arm itself 60 
seconds after disarming with the Remote Control Transmitter. Automatic rearm 
will cancel if any door is opened before the 60 second timer has elapsed. 

 
 

IGNITION CONTROL DOOR LOCKS (

OPTIONAL

If the vehicles door locks have been interfaced to the Security System, the 
Security System will automatically lock the vehicles doors when the ignition is 
turned “ON” and/or unlock the vehicles doors when the ignition is turned “OFF”.   
 

Note: 

If any door is open when the ignition is turned “ON”, the Security 
System will not automatically lock the vehicles doors.  

 

LED STATUS INDICATOR 

1. 

LED OFF:  Security System is disarmed 

2. 

LED ON:  Security System is in valet mode 

3. 

LED FAST FLASHING:  Automatic arming timer is counting down 

4. 

LED FLASHING:  Security System is armed 

5. 

LED FLASHING AFTER DISARMING:  Security System Violation 

 

a) 

2 Flashes…pause- Trunk / Hood Violation  

b) 

3 Flashes…pause- Door Trigger Violation 

Reviews: