background image

Page  1 of 19

AudioCodes™ MP-104 Gateway Quick Start Installation Guide

August 2004

AudioCodes™ MP-104 Gateway

Quick Start Installation Guide

INTRODUCTION

This quick start guide contains information about how to install and configure the v4.4 Audio-
Codes™ MP-104 Gateway. This gateway is the latest version that is available through the
Inter-Tel

®

 CommSource™ division.

PARTS

This shipment consists of the following items:

AudioCodes MP-1xx Media Gateway Fast Track Installation Guide

AudioCodes MP-1xx CD-ROM

Inter-Tel IP Devices CD-ROM (Part No. 827.9162)

Inter-Tel AudioCodes Quick Start Guide

Power cord

ADDITIONAL SUPPLIES NEEDED

In addition to the previously listed parts, you will also need an Ethernet cable.

SYSTEM REQUIREMENTS

The following lists the system requirements for installing the AudioCodes MP-104 Gateway:

Internet Protocol Resource Card (IPRC) firmware version 1.5.2, 8.2.0, or later

Axxess

®

 v7.0 or later

The AudioCodes MP-104 Gateway also must meet the following telephony requirements:

Loop Current:

 20mA, preferably down to an 18mA loop current (25 to 45mA may not

suffice and will increase the risk of poor audio).

Line Voltage:

 24 to 48vdc. Must pass the test called out in EIA/TIA-464B 4.1.2.3.3

(generally 42.5V ~56.5V).

Ring Voltage:

 40 to 150 vac ring voltage 20 to 30 Hz. Must pass the requirements

called out in EIA/TIA-464B 4.1.2.2.5 (generally 55~130Vrms for Class A;
40~130Vrms for Class B).

Db Levels:

 At least +3dBm without distortion into a 600 ohm load. Must pass the

transmission requirements called out in Section 5 of EIA/TIA-464B.

SYSTEM DATABASE PROGRAMMING 

The IPRC firmware version determines how Axxess is programmed to support the gateways.
For details about system database programming, refer to the documents listed below. 

If you are installing the gateway on a:

v1.5.1 firmware

 

IPRC

, see the latest version of the 

IP Devices Manual

v8.2.x or later firmware IPRC

, see the

 Addendum to the v8.0 Installation and Mainte-

nance Manual

.

Document Part Number 835.2741-4

A946/3852A

© Inter-Tel, Inc. August 2004 printed in USA

Summary of Contents for MP-104




















Reviews: