background image

1

 

Introduction

Thank you for purchasing this product. Before using the product, read through 
the user manual to ensure that you will use the product correctly. Please keep 
this manual for future reference.

 

Features

• Modular microphone system comprised of an ES Series capsule, gooseneck 

assembly, and power module.

• RGB LEDs built into both the desk stand power module and gooseneck 

assembly indicate the on/off status of the microphone.

• The capacitive touch switch can be set to any of three operating modes: 

“touch-on/touch-off”, “touch-to-talk” and “touch-to-mute”.

 

Safety precautions

Although this product was designed to be used safely, failing to use it correctly 
may result in an accident. To ensure safety, observe all warnings and cautions 
while using the product.

 

Cautions for the product

• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a 

hot, humid or dusty place.

 

Notes on use

• Do not swing or pull the product. Doing so may cause disconnection or 

damage.

• The circuitry in the microphone takes about 30 seconds to stabilize after power 

is supplied. You may hear some audio disturbance during startup.

• The connectors are equipped with a special RFI-shielding mechanism. If you 

remove or replace the connector, you may adversely affect the microphone’s RFI 
immunity. The Audio-Technica Crimp Tool (ATCT) and shield parts are required to 
shorten the cable and reinstall the connector while maintaining the RFI immunity.

• Install the microphone on a flat, unobstructed mounting surface. Make sure 

that the sound source is not below the mounting surface.

• Depending on the surface finish of a table, the desk stand power module may 

leave marks on the table.

• Do not excessively bend the gooseneck assembly, rotate the ends of the 

capsule, or pull on them. Doing so may cause disconnection or malfunction.

• The product is a modular system comprised of a microphone element, 

gooseneck assembly and power module. Make sure the parts are firmly 
attached before use.

• Do not remove the rubber O-ring on the power module connecting part at the 

lower section of the gooseneck assembly.

• When attaching parts, remove the black cap on the capsule connecting part 

of the gooseneck assembly.

 Do not remove the silicone part at the end of 

the capsule connecting part.

Silicone part

Do not remove

 

Switch settings

To reduce low-frequency ambient noise (such as footsteps or air conditioning 
noise), room reverberation, and mechanically coupled vibrations as much as 
possible, turn on the low-cut filter switch (

) on the bottom of the power 

module.

ES925H6/DS3

ES925H12/DS3

ES925H15/DS3

ES925H18/DS3

ES925H21/DS3

ES925H24/DS3

User Manual

HYPERCARDIOID CONDENSER 

MODULAR GOOSENECK MICROPHONE 

WITH 3-PIN DESK STAND POWER MODULE

Summary of Contents for ES925H6/DS3






Reviews: