background image

* All Pictures In This Manual Are For Illustrative Purposes Only. Actual Product May Vary.

© 2021 United States Stove Company, 227 Industrial Park Rd., South Pittsburg, TN 37380 

Ph. 800-750-2723

THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE.

Owner’s Instruction and Operation Manual

U.S. Environmental Protection Agency 

Certified  to  comply  with  2020  particulate 

emissions standards.

SAFETY NOTICE: If this heater is not properly installed, a house fire may result. 
For  your  safety,  follow  the  installation  instructions.  Never  use  make-shift 

compromises during the installation of this heater. Contact local building or 

fire officials about permits, restrictions and installation requirements in your 

area. NEVER OPERATE THIS PRODUCT WHILE UNATTENDED.

CAUTION! Please read this entire manual before you install or use your new room 
heater. Failure to follow instructions may result in property damage, bodily injury, 

or even death. Improper Installation Will Void Your Warranty!

Save These Instructions In A Safe Place For Future Reference.

 CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon 
monoxide, which is known to the State of California to cause 
cancer, birth defects, and/or other reproductive harm. For 
more information, go to

 www.P65warnings.ca.gov

AP5501S

852715K-0204K

R

Report Number: F19-549

Certified  to  ASTM  E1509-12  (2017) 

and Certified to ULC-S627-00-REV1

Mobile Home Approved 

Model Number:

Summary of Contents for AP5501S

























































Reviews: