P/N 80-9150-0064-010 Rev A
An ASSA ABLOY Group brand
2
(2) 8-32 x 3/4"
Flat Head
Combination Screws
Directions
9b
Touchscreen Cable
Routing
(2) 8-32 x 3/4"
Flat Head
Combination Screws
1
EASY
EXT-PWR / REMOTE /
MOTOR
Easy /
Advanced
Mode
ADVANCED
Touchscreen
Cable
Connector
EXT-PWR / REMOTE /
MOTOR
6
"Z" Fold
Outside Assembly
Touchscreen
Cable
Escutcheon Screw
(1) 10-32 x 3/4" Pan Head
With Star Washer Screw
3
3b
4
5
9
10
11
12
13
Motor Cable
Support Assembly Screws
(2) 10-32 x 2-1/2" Flat
Head Machine Screws
Inside Assembly
7. Attach the touchscreen cable connector to the inside escutcheon PC board
header as illustrated.
8. Select
EASY
or
ADVANCED Mode
using the switch on the back of the PC board.
9. Slide inside escutcheon over inside support assembly.
CAUTION
:
a. Position motor cable against inside support assembly. Avoid pinching wires
against the steel shank of the assembly.
b. “Z” fold touchscreen wire cable and lay against the back recessed area of
the escutcheon assembly. Position and bend wires to prevent binding when
installing the escutcheon over the support assembly.
10. Install and secure the 10-32 x 3/4" pan head screw through the center of the
battery housing into the barrel nut of the outside assembly.
11. Slide on inside lever and push in to attach.
12. Insert four (4) AA alkaline batteries. The lock responds, “
Welcome to the
Arrow Digital World
.”
Note: Refer to other side of this Quickstart Guide for
EASY Mode
programming directions
prior to the completion of step 13. For more details and
Advanced Mode
programming,
please refer to the complete Programming Instructions.
13. Install battery cover and tighten hex head screw with Allen wrench
provided with lock.
3a
8
7
HARDWARE INSTALLATION
1
Quickstart Guide
Components
Quick Start Instructions
Installation Instructions
Door Marker
Outside Touchscreen Assembly
Inside Support Assembly
Inside Escutcheon Assembly:
• Inside Support Assembly
• Inside Escutcheon
• Inside Lever Handle
• Battery Cover
4 AA Alkaline Batteries
Latchbolt
Strike
Allen Wrench 3/32” (2.5 mm)
Screw Pack (7 screws)
2 Keys (If Cylinder Included)
For Technical Assistance call Arrow:
1-800-221-6529.
Before installation, disassemble the inside assembly, as shown above, by
removing the inside lever with the lever removal tool provided and separating
the support assembly from the inside escutcheon. Remove the battery cover
from the inside escutcheon by unscrewing the hex screw, using the Allen wrench
provided, and sliding the battery cover up and off (the hex screw does not come
completely out). The outside assembly remains assembled.
Refer to complete installation instructions for more information if changing hands
or adjusting door thickness is required.
1. Install latchbolt in door. Attach with two screws provided.
Note: Be sure that bevel edge of bolt faces strike.
2. Install strike on the door frame.
3. Insert outside assembly through door.
a. Guide motor cable (red and black wires) through 2-1/8" diameter hole.
b. Guide touchscreen cable through 3/4" diameter upper hole.
4. Guide motor cable through rectangular hole on inside support assembly.
5. Slide inside support assembly over outside assembly, lining up top and
bottom screw guides with holes in door. Secure both assemblies with
(2) 10-32 x 2-1/2" flat head machine screws. Do not over-tighten.
6. Attach motor cable connector to the inside escutcheon PC board header
marked “MOTOR.”
