background image

Model No.

EDA86

Owner's Manual & Assembly Instructions

      XP01

2,4 m x 1,7 m    247,7 cm x 174,6 cm          253,4 cm    181,0 cm      201,0 cm           240,7 cm     167,6 cm     197,8 cm    110,5 cm   175,9 cm

                                           Exterior Dimensions                     Interior Dimensions                    Door

       *Approx.                Base                   (Roof Edge to Roof Edge)                      (Wall to Wall)                       Opening
           Size                    Size                  Width       Depth       Height           Width       Depth      Height       Width     Height

          8' x 6'          97 1/2" x 68 3/4"          99 3/4"     71 1/4"      79 1/8"           94 3/4"        66"         77 7/8"       43 1/2"    69 1/4"

715990111

  Storage Area:     43 Sq. Ft.

271 Cu. Ft.

                   4,0 m

2

           7,7 m

3

BUILDING DIMENSIONS  

* Size rounded off to the nearest foot

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

Summary of Contents for EDA86






























Reviews: