Garden Tier Lights
LVG546
Installation Instructions
ASSEMBLING TIER LIGHT HEAD
There are four separate components to the
Tier Light head as shown : fig 1
1. Fit top cap onto rim of lens and ensure that
it snaps firmly in place.
2. Fit small plastic ring onto Tier Light lens
with textured surface upwards. Use thumbs
to push the ring over lens until it snaps firmly
in centre locating groove.
3. Fit globe socket and terminal pin housing
onto the lower part of lens. Locate the
bayonet type slots, twist and lock into place.
CONNECTING THE LIGHTS TO
LOW VOLTAGE CABLE
IMPORTANT: Low voltage cable is
NOT to be used for 240 volt wiring.
NOTE: Cable lengths greater than 18 metres
may cause a small reduction in brightness to
Tier Lights furthest along the cable from the
transformer.
1. If you are adding Tier Lights to your
existing garden lighting, first check that the
transformer is powerful enough to illuminate
lights
(See chart on page 2 Maximum Load Capacity
of Arlec Garden Lighting Transformers).
2. Additional cable can be joined to your
existing cable either at the end of the length,
or joined anywhere along the cable using an
Arlec Cable Connector (LV700). Arlec low
voltage cable is completely weatherproof and
may be used above or below ground.
3. Lay low voltage cable out in position in
readiness for connecting Tier Lights.
4. Plug the transformer into a household
powerpoint and switch “ON”. This will
enable you to check light connections during
installation.
This operation is completely safe because the
wiring is only carrying a low 12 volt.
5. At the location of the new Tier Light form
the low voltage cable into a large loop.
6. Lay the flat side of the cable across the pin
terminals at the base of the tier light.
Keep these instructions in a safe place for future reference
CPIN002245
Lens & Globe Holder
Assembly
4Watt Globe
Stake
Cable
Locating
Studs
Lower Tier Collar
Assembly
Top Cap
Fig 1.
For all Sales & Warranty enquiries
Arlec Australia Pty Ltd. (A.C.N. 009 322 105)
Building 3, 31- 41 Joseph Street,
Blackburn North, Victoria, 3130
P.O. Box 1065, Blackburn North LPO
Blackburn North, 3130
Phone: (03) 9982 5111
Fax: 1300 360 650
Email: [email protected]
© This instruction leaflet is subject to copyright and
must not be reproduced, copied or otherwise used
in any way or for any purpose without the consent in
writing of the owner,
Arlec Australia Pty Ltd (A.C.N. 009 322 105).
Arlec Warranty*
Arlec guarantees this product against defects of
materials and workmanship for a period of 1 year
from the date of purchase provided the product
is used for its proper purpose, in accordance with
Arlec’s recommendations and within such voltage
and current limits as are specified by Arlec in relation
to the product. Arlec will at its own option and cost
make good, or replace this product with the same
or similar product and return it to you, or provide
a credit for any product manufactured or supplied
by it, which proves to be defective within the limits
set out above provided that no repairs, alterations or
modifications to the product have been undertaken
or attempted by anyone, other than Arlec or its
authorized agents. Should you wish to make a claim
under this guarantee, the product and proof of
purchase must be returned pre-paid by you to the
place of purchase.
This guarantee is in addition to and does not take
away from any other rights and remedies you may
have under any relevant law.
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Proof of Purchase
Please retain your proof of purchase for all warranty
claims.
*Excludes Globes
CPIN002245
LVG546 Instructions.indd 1-2
5/08/11 1:47 PM
