background image

INSTALLATION AND OPERATING INSTRUCTIONS

PATRIOT PORTABLE LIFT

TM

450 LB. MAXIMUM CAPACITY (PRO POOL LIFT)

MANDATORY

LEAVE THIS MANUAL WITH LIFT OWNER

9889 GARRY MORE LANE

MISSOULA, MT 59808

1-888-687-3552

FAX: 406-549-2602

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1.

READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT
IS INSTALLED AND OPERATED PROPERLY

AS PER INSTRUCTIONS.

2.

WARNING- TO REDUCE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS
PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.

3.

WARNING- DO NOT PERMIT CHILDREN TO PLAY ON THIS PRODUCT.

4.

WARNING- NEVER APPLY DIRECT WATER PRESSURE TO ELECTRONIC COMPONENTS.

5.

SAVE A COPY OF THESE INSTRUCTIONS.

AQUA CREEK, LLC 2003

APRIL 2008

- READ CAREFULLY-

Check entire box and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the figures and parts listed in this document. It is critical that all
parts be carefully inspected by the installer prior to installation to ensure that no damage occurred in
transit and that a damaged part is not used. If any damage occurred in transit, Aqua Creek Products,
LLC must be notified within three days of receipt of unit. Proper installation cannot be overstressed, as

a

i

mpr

ope

r

 

i

ns

t

a

l

l

a

t

i

on 

voi

ds

 

Aqua

 

Cr

e

e

k’

s

 

wa

r

r

a

nt

a

nd 

ma

a

f

f

e

c

t

 

t

he

 

s

a

f

e

t

of

 

t

he

 

us

e

r

.

PATRIOT LIFT

WITH OPTIONAL

HEADREST AND

CHEST STRAP

Summary of Contents for PATRIOT PORTABLE LIFT


















Reviews: