background image

 

 

 

 

 

 

 

 

 

 
 

 

ATX Power Connector 

AGP 8X Expansion Slot
supports 8X AGP card (2.1GB/S) and ADD 
card (for MX4SG-4DL & MX4SG-4DN)

 

478-pin CPU socket with Voltage and 
Frequency Auto-detection that supports 
Intel

®

 Pentium

®

 4 1.6~3.20GHz+ CPU

 

Intel

®

 865G Chipsets (for MX4SG-4DL & MX4SG-4DN) 

Intel

®

 848PB Chipsets (for MX4SPB-N) 

CPUFAN Connector 

184-pin DIMMx4 supports
128bit dual channel DDR400/333/266 
Max. To 4GB (for MX4SG-4DL & MX4SG-4DN) 
184-pin DIMMx2 supports 
128bit DDR400/333/266 
Max. To 2GB (for MX4SPB-N) 

IDE Connector x 2
(ATA33/66/100 supported) 

IrDA Connector 

Onboard AC’97 CODEC 

AUX-IN Connector 

32-bit PCI Expansion Slot x3 

           SYSFAN2 Connector 

JP14 CMOS Data Clear Jumper 

Low ESR Capacitors 

S/PDIF Connector 

JP28 PS2 KB/Mouse Wakeup Jumper 

CD-IN Connector 

PS/2 Mouse 

Connector

SPP/EPP/ECP Parallel Port 

USB 2.0

Ports 

RJ45 10/100/1000

 LAN Jack 

PS/2 Keyboard 

Connector

USB 2.0 Ports 

COM 1 Port 

VGA Port

(For MX4SG-4DL and 

MX4SG-4DN) 

Line-In 

MIC-In 

Speaker 
Out

 

AOpen reserves the right to revise all the specifications and information contained in this document, which are subject to change without notice. 

Front Audio Connector 

USB 2.0 Connector x2 

 Front Panel Connector 

Case Open Connector 

Serial ATA Port x2 

 Supports 150

 

MB/s Transfer Rate

FDD Connector 

SYSFAN1 Connector 

Resetable Fuse 

4-pin 12V ATX Power Connector 

Broadcom Gigabit LAN Chip (MX4SG-4DL) 

Broadcom 10/100 Mbps LAN Chip 

(MX4SG-4DN & MX4SPB-N)

 

4 Mb Flash ROM BIOS 

AGP Protection LED 

COM2 connector

STBY LED 

Summary of Contents for MX4SG-4DL









Reviews: