clockwise only until you feel the brush cap stop. If the
brush cap is tightened too tightly, it will force the
brush spring past the carbon brush and will cause
damage to the commutator.
CHANGING THE BLADE ASSEMBLY
If your clipper blades no longer cut properly (be sure
to try more than one blade, since blade currently
being used may be dull), it could be that your blade
drive assembly needs replacement.
To change the blade drive assembly:
1.
Unplug your clipper.
2.
Remove blade set.
3.
Remove four housing
screws with philips
screwdriver.
4.
Turn clipper over and
remove cover.
5.
Before attempting to
remove the blade
drive assembly, you
must remove the
blade hinge first.
Remove the
two blade hinge
screws
(Diagram H). When
removing the blade
hinge, you will notice
a small spring set in
between the hinge
and the lower hous-
ing (Diagram I). Make
sure that this part
does not get lost
when replacing the
blade drive assembly.
6.
Remove blade drive
mounting screws
(Diagram J).
7.
NOTE: Before remov-
ing blade drive assem-
bly, note the way it is
positioned (this will
help you in reassem-
bly). Remove blade
drive assembly
(Diagram K).
8.
Drive bearing should be
at its lowest position, if
not, move it with your
finger to lowest position
(Diagrams L and M).
9.
Align screw holes of
new blade drive assem-
bly and press down
level at the screw holes
(Diagram N).
10. Reassemble blade
drive mounting screws
(Diagram J).
11. Be sure the hinge
spring is in its place
before attempting to
replace the blade hinge
and screws (Diagram
O). When replacing the
hinge screws, place
screw in the screw hole
and
slowly
turn count-
er-clockwise until you
feel the screw drop into
place. This assures the
screw is properly
aligned within the hole
threads. Turn screw
clockwise to tighten,
just until snug.
DO NOT
OVER-TIGHTEN.
12. Replace cover and turn
clipper over.
13. Replace housing screws. (Short screws in back
by cord—long screws in front by blade).
Congratulations –
you just went First Class when you bought
this Andis Clipper. Careful workmanship and
quality design have been the hallmarks of
Andis products since 1922.
BLADE
DRIVE
MOUNTING
SCREWS
DIAGRAM J
DIAGRAM H
HINGE
SCREWS
DIAGRAM I
SPRING
INCORRECT
POSITION
OF DRIVE
BEARING
CORRECT
POSITION
OF
DRIVE
BEARING
DIAGRAM L
DIAGRAM M
DIAGRAM N
DIAGRAM K
DIAGRAM O
®
Form # 27074 Rev. N ©2004 Andis Company, USA Printed in U.S.A.
Detachable Plus
®
MODEL AG
Clipper
Andis Model AG
Detachable Blades
are compatible with
Oster Model A5
LIMITED WARRANTY
This Andis product is warranted against defective material or workmanship
for one year from the date of purchase. All implied warranties arising and by
virtue of State law shall also be limited to one year. Any Andis product deter-
mined to be defective in material or workmanship during the warranty period
will be repaired or replaced without cost to the consumer for parts and labor.
The defective product must be returned with proof of purchase and $6.50 to
cover cost of handling, to any Authorized Andis Repair Station or to: Andis,
1800 Renaissance Blvd., P.O. Box 085005, Racine WI 53408-5005 USA
or IN
CANADA
to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse,
Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the
nature of the problem. Due to foreign matter sometimes found in hair, clipper
blades or resharpening of blades are not subject to the one year warranty. The
blade set has a 10 Day Limited Warranty. If the blade set fails to cut, it will be
resharpened free of charge if returned within 10 days of purchase. Send your
blade set postage prepaid with the original purchase receipt to: ANDIS COM-
PANY, ATTENTION: Service Department, 1800 Renaissance Blvd, Sturtevant,
Wisconsin 53177 (U.S. & Canada only). Andis will not be liable under this war-
ranty for any defect, failure or malfunction of any of its products caused by
normal wear, abuse, misuse, unauthorized adjustments or disassembling.
Andis will not be liable for any consequential damages resulting from any
defect in material or workmanship of any of its products. Some States do not
allow limitations on how long an implied warranty lasts or exclusion or limi-
tation of incidental or consequential damages, so the above limitations or
exclusions may not apply to you. The Warranty gives you specific legal rights,
and you may also have other rights which may vary from State to State.
Date Purchased ___________________________ Model ____________
KEEP THIS FOR YOUR RECORDS
FACTORY REPAIR SERVICE
When the blades of your Andis Clipper become dull
after repeated use, it is advised to send your blades
to an Andis Authorized Service Station mentioned
below for resharpening. If you wish your clipper to be
serviced as well, they should be carefully packed and
mailed either Parcel Post Insured, or U.P.S.
Please see enclosed slip sheet
for all Andis Authorized repair stations
