![background image](http://html1.mh-extra.com/html/amt/pangaea-cp-100fx/pangaea-cp-100fx_quick-start_2936358001.webp)
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
AMT
electronics.com
Quick Start
1.
Turn the volume knob on your guitar all the way down to zero.
2.
If you want to use your effect pedals connect the last pedal’s output to Pangaea’s
Input
, just like you would normally connect it to a guitar amp. You can also plug your
guitar directly into Pangaea! See the diagram below.
3.
Use 1/4’’ TRS cable to connect Pangaea’s
Main Out
to your playback system or simply plug your headphones into
Phones Out
.
4.
Connect the included AC adapter to Pangaea and plug it into a power outlet.
5.
Turn on your playback system.
6.
Now slowly turn up your guitar’s volume. Watch out, it may get pretty loud!
7.
Too loud? Press
2/VOL
button to adjust volume. Turn
Navigation/Confirm
knob to choose between Master and Phones volume. Press it to edit the values. Press
Esc
to return to the home screen.
8.
Browse pre-programmed tones using the
Navigation/Confirm
knob. Press it to recall the selected preset.
9.
Press
Edit
button to edit a preset. You’ll see effect blocks:
RF
(Resonance Filter);
GT
(Noise Gate);
CM
(Compressor);
PR
(Preamp Simulator);
PA
(Power Amp
Simulator);
IR
(Cabinet Simulator);
EQ
(Parametric EQ);
DL
(Delay);
PH
(Phaser);
FL
(Flanger);
CH
(Chorus);
ER
(Early Reflections);
RV
(Reverb) and
TR
(Tremolo). Turn
Navigation/Confirm
knob to select the desired effect block and press it to enable/disable the effect. Press
Edit
again to tweak effect’s parameters.
When you’re done press
Esc
several times to get back to the home screen.
10.
Out of tune? Activate the tuner by pressing
5/TUNER
button.
11.
While on the home screen press
Esc
to see currently chosen Impulse Response’s name.
12.
Download full User’s Guide from www.amtelectronics.com
AMT
PANGAEA
IR CONVOLUTION PLAYER
CP100FX
INPUT THRU L BAL OUT R OUT LR
PHONES AUX IN USB SD CARD S/PDIF
OUT
TAP
FX
DOWN CONFIRM UP
1 2 3 4 5
ATT IN VOL EQ SYS TUNER
IN CLIP OUT CLIP
Esc
EDIT
CONFIRM
DRIVE
AMT
PANGAEA
IR CONVOLUTION PLAYER
CP-100FX
www.amtelectronics.com
Rev A (For use with firmware V1.5.6)
©2016 AMT Electronics. Omsk, Russia