1
CS-SLVP-ADA-00
Accessory Basket with Capsule Neuron 2
Quick Installation and Maintenance Instructions
Medical Facility Responsibility
!
WARNING:
It is the responsibility of the end user to ensure all aspects of installation are covered by following the full manual found at
https://www.amico.com/products/equipment-mounts/patient-monitor/capsule-monitor-mounts/capsule-neuron-mounts
.
Installation Tools
1x #2 Phillips Head Screwdriver
1x #3 Phillips Head Screwdriver
Hex Key: 1/8"
NOTE:
Tools for installation not provided by Amico Accessories. Verify the weight of the monitor to be mounted. This product is rated at 20 lbs
total, including 5 lbs in the basket. The
CAPSULE NEURON 2
must be mounted with the
NIBP PACK
* as shown in
Figure 2
. The
CAPSULE
NEURON 2
can only be mounted to
CS-SLVP-ADA-00
without the
NIBP PACK
in a non-flush configuration.
Mounting to AHM-_4-_/SSM-_4-_
Insert 3x
FLAT HEAD SCREWS
through the top of the
MOUNTING PLATE
and into the
DISK
as shown in
Figure 1
using a 1/8" Hex Key/bit. Use the provided 3/16" Hex Key to
tighten and secure.
MOUNTING PLATE
[X-CS-NRN2-BSK-PLT]
(A PART OF CS-SLVP-ADA-00)
3x
FLAT HEAD SCREWS
[H-FHCS-1032-58]
DISK
[MON-SWIV-DISK-T]
(A PART OF AHM-_4-_ OR SSM-_4-_)
Installation Tools (not provided)
Mounting to AHM-_4-_/SSM-_4-_
1. Insert 3 x FLAT HEAD SCREWS through top of MOUNTING
PLATE and into DISK as shown in (
Figure 1)
below using
a 1/8" hex key/bit. Use the provided 3/16" hex key to
lighten and secure.
WARNING:
It is the responsibility of the end user to ensure all aspects of installation are covered by following the full manual found at
http://www.amico.com/products/capsule-neuron-mounts.
NOTE:
Tools for installation not provided by Amico Accessories. Verify the weight of the monitor to be mounted. This product is rated at 20 lbs
TOTAL
,
including 5 lbs in the basket. The
CAPSULE NEURON 2
must be mounted with the
NIBP PACK*
as shown in
(Figure 2)
. The C
APSULE NEURON 2
can only be
mounted to
CS-SLVP-ADA-00
without the
NIBP PACK
in a non-flush configuration.
Installation Reference
CAPSULE NEURON 2
(NOT PRODVIDED)
3 X
FLAT HEAD SCREW
[H-FHCS-1032-58]
Accessory Mounting
Accessory Basket
with Capsule Neuron 2
CS-SLVP-ADA-00
Quick Setup to Attach Accessory Basket to Amico Mount
For use with Capsule Neuron 2 (Vitals Plus)
1. Insert 4 x
PAN HEAD SCREWS
through 4 x
LOCK WASHERS
through the back of the
MOUNTING PLATE
and into the
device
(CAPSULE NEURON 2 AND NIBP PACK*)
as shown
below.
MOUNTING PLATE
[X-CS-NRN2-BSK-PLT]
(A PART OF CS-SLVP-ADA-00)
DISK [MON-SWIV-DISK-T]
(A PART OF AHM-_4-_
OR SSM-_4-_)
*NIBP PACK
(NOT PRODVIDED)
4 X
LOCK WASHER
[H-WLM-M4]
4 X
PAN HEAD SCREW
[H-PHMS-M4-14]
MOUTING PLATE
[X-CS-NRN2-BSK-PLT]
(PART OF CS-SLVP-ADA-00)
Hex Key: 1/8"
Phillips Head Screwdrivers: #2, #3
Hex Key: 1/8"
CS-SLVP-ADA-00
Figure 1
For Use with Capsule Neuron 2 (Vitals Plus)
Insert 4x
PAN HEAD SCREWS
through 4x
LOCK WASHERS
through the back of the
MOUNTING PLATE
and into the device (
CAPSULE NEURON 2
and
NIBP PACK*
) as shown
in
Figure 2
.
MOUNTING PLATE
[X-CS-NRN2-BSK-PLT]
(PART OF CS-SLVP-ADA-00)
4x
LOCK WASHERS
[H-WLM-M4]
4x
PAN HEAD SCREWS
[H-PHMS-M4-14]
*NIBP PACK
(NOT PROVIDED)
CAPSULE NEURON 2
(NOT PROVIDED)
Installation Tools (not provided)
Mounting to AHM-_4-_/SSM-_4-_
1. Insert 3 x FLAT HEAD SCREWS through top of MOUNTING
PLATE and into DISK as shown in (
Figure 1)
below using
a 1/8" hex key/bit. Use the provided 3/16" hex key to
lighten and secure.
WARNING:
It is the responsibility of the end user to ensure all aspects of installation are covered by following the full manual found at
http://www.amico.com/products/capsule-neuron-mounts.
NOTE:
Tools for installation not provided by Amico Accessories. Verify the weight of the monitor to be mounted. This product is rated at 20 lbs
TOTAL
,
including 5 lbs in the basket. The
CAPSULE NEURON 2
must be mounted with the
NIBP PACK*
as shown in
(Figure 2)
. The C
APSULE NEURON 2
can only be
mounted to
CS-SLVP-ADA-00
without the
NIBP PACK
in a non-flush configuration.
Installation Reference
CAPSULE NEURON 2
(NOT PRODVIDED)
3 X
FLAT HEAD SCREW
[H-FHCS-1032-58]
Accessory Mounting
Accessory Basket
with Capsule Neuron 2
CS-SLVP-ADA-00
Quick Setup to Attach Accessory Basket to Amico Mount
For use with Capsule Neuron 2 (Vitals Plus)
1. Insert 4 x
PAN HEAD SCREWS
through 4 x
LOCK WASHERS
through the back of the
MOUNTING PLATE
and into the
device
(CAPSULE NEURON 2 AND NIBP PACK*)
as shown
below.
MOUNTING PLATE
[X-CS-NRN2-BSK-PLT]
(A PART OF CS-SLVP-ADA-00)
DISK [MON-SWIV-DISK-T]
(A PART OF AHM-_4-_
OR SSM-_4-_)
*NIBP PACK
(NOT PRODVIDED)
4 X
LOCK WASHER
[H-WLM-M4]
4 X
PAN HEAD SCREW
[H-PHMS-M4-14]
MOUTING PLATE
[X-CS-NRN2-BSK-PLT]
(PART OF CS-SLVP-ADA-00)
Hex Key: 1/8"
Phillips Head Screwdrivers: #2, #3
Hex Key: 1/8"
CS-SLVP-ADA-00
Figure 2
Installation Reference
CS-SLVP-ADA-00
HARDWARE
