background image

1

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch;  

 

 

do not use any phone in your    

  building.
 

•  Immediately call your gas supplier  

 

 

from a neighbor’s phone. Follow  

 

 

the gas supplier’s instructions.

 

•  If you cannot reach your gas 

 

 

supplier, call the fire department.

Installation and service must be performed 
by a qualified installer, service agency or 
the gas supplier.

WARNING:  If the information in these

instructions is not followed exactly, a fire 

or explosion may result causing property 

damage, personal injury or death.

INSTALLER:
• 

AFFIX THESE INSTRUCTIONS TO OR ADJACENT   
TO THE WATER HEATER.

OWNER:
• 

RETAIN THESE INSTRUCTIONS AND WARRANTY 
FOR FUTURE REFERENCE. RETAIN THE ORIGINAL 
RECEIPT AS PROOF OF PURCHASE.

Table of Contents   ......................................................    2

Residential Gas 

Water Heater

with the Flame Guard

Safety System

To obtain technical, warranty, or service assistance during or after 
the installation of this water heater, or call toll free

1-800-999-9515

When calling for assistance, please have the following 
information ready:

1. Model 

number

2. 

7 digit product number

3. Serial 

number

4. 

Date of installation

5. 

Place of purchase

NATURAL & L.P. GAS MODELS

Installation

Instructions and

Use & Care Guide

(Flammable Vapor Ignition Resistant)

319407-001

September 2010

LOW LEAD

COMPLIANT

http://waterheatertimer.org/Review-Kenmore-Energy-Star-Water-Heater.html

Summary of Contents for Residential Gas Water Heater

































Reviews: