INSTALLATION INSTRUCTIONS
753026-100 Rev. G
© American Standard Inc. 2007
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
TOWN SQUARE®
5' x 42"™
WHIRLPOOL/BATHING POOL
2748.XXXW SERIES
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your
new bath is shipped to you after careful
inspection. The whirlpool version is completely
assembled with pump, motor, and system piping.
All you need to finish the installation are your
selected fittings and electrical connections for a
whirlpool. To insure maximum performance and
pleasure from this product, please follow the
instructions and cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately. After inspection and during installation, protect the bath from construction damage. After installation, and
before enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the
safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or
piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing
materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess
installations).
If installing American Standard 2555.901 "Town Square" deck mount bath filler, please refer to hole
drilling location above.
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Tile Bead Kit (P/N 751755-200)
• 5 Foot Apron 9460.018
• Safe-T-Heater 9075.120*
List of Required Components (not included):
• Drain 1594.170
• Bath Filler
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
C/L
FOR SPOUT
& VALVES
FOR HAND
SPRAY
FITTINGS
DECK
EDGE OF
FITTINGS
DECK
29-7/8
(759mm)
TO END
OF TUB
1-1/2
(38mm)
1-1/2
(38mm)
1-1/2
(38mm)
4-1/2
(114mm)
2-1/2
(64mm)
4-1/2
(114mm)
5
(127mm)
DRAIN
HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"
DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY
SAFE-T-HEATER
REMOVABLE
BLANK
59-1/2"
(1511mm)
INTEGRAL
FITTING DECK
2-1/2" X 14"
(64 X 356mm)
29-7/8"
(759mm)
41-5/8"
(1057mm)
ON/OFF
SWITCH
SUCTION
OUTLINE OF CUTOUT
58-1/4" X 40-1/4"
(1480 X 1022mm)
PROVIDE ACCESS
TO PUMP FOR
SERVICE ON ALL
INSTALLATIONS
C/L OF
DRAIN
OUTLET
FLOOR CUTOUT
5" X 12"
(127 X 305mm)
3/4"
(19mm)
14-1/2"
(368mm)
5-1/4"
(133mm)
JETS (6)
3"
(76mm)
OUTLINE OF
SKID RESISTANT
SURFACE
LEVELING STRINGER
(NOT FOR SUPPORT)
1-1/2" N.P.T.
THREADS
2"
(51mm)
5-3/4"
(146mm)
C/L OF
OVERFLOW
21"
(533mm)
23"
(584mm)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2" O.D.
TAILPIECE
3/4"
(19mm)
3-1/8"
(79mm)
PUMP
EDGE OF
FLOOR
CUTOUT
PUMP
GENERAL SPECIFICATIONS FOR 2742 WHIRLPOOL
71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm)
115 Lbs. (52 Kg.)
690 Lbs. (313 Kg.)
69 Gal. (261 L)
60 Gal. (227 L)
41 x 21-1/2 In. (1041 x 546mm)
62 x 31-1/2 In. (1574 x 800mm)
14-1/4 In. (362mm)
33 Lbs./Sq.Ft. (163 Kgs./Sq.m)
27.8
55.7
2.1 HP, 14.4 AMPS ,120V.
WHIRLPOOL PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
