background image

RECOMMENDED TOOLS AND  MATERIALS

Putty Knife 

 

Regular Screwdriver  

Adjustable Wrench 

      Sealant 

 

Tape Measure

Hacksaw 

 

Wax Ring/Gasket 

 

Flexible Supply Tube 

      Closet Bolts  

Carpenters Level

1

   REMOVE OLD TOILET

a.  Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.  Disconnect and remove supply line. NOTE:

 If replacing valve, first shut off main water supply!

c.  Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.  Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
     NOTE: 

Mounting surface must be clean and level

 before

 new toilet is installed!

S

A

VE FOR FUTURE USE

3

2

CLOSET FLANGE

CLOSET BOLTS

7 3 0 2 010 - 10 0   Rev. A

A

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

P r o d u c t   n a m e s   l i s t e d   h e r e i n   a r e   t r a d e m a r k s   o f   A S   A m e r i c a ,   I n c .
©   A S   A m e r i c a ,   I n c .   2 0 1 3

NOTE: 

Pictures may not exactly define contour of china and components.

ROUGHING-IN DIMENSIONS:  

NOTE: 

Distance from wall to closet flange centerline must be as listed below:

5

4

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and 
install wax ring evenly around waste flange (horn), with 
tapered end of ring facing toilet. Apply a thin bead of 
sealant around toilet base.

POSITION TOILET ON FLANGE

a.  Unplug floor waste opening and install toilet on closet flange so bolts project
     through mounting holes.
b.  Loosely install retainer washers and nuts. Side of washers marked "THIS
     SIDE UP" 

must 

face up!

WAX RING

SEALANT

WASHER

NUT

FLANGE

BOLT

T

HIS

 SIDE UP

 

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, 
please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your 
installation conforms to local codes.

!

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide 
into place 6" (152 mm) apart and parallel to wall.

LOFT

®

1.28 GPF ONE-PIECE TOILET

Model 2535 – Compact Elongated Right Height™ with Seat

INSTALLATION INSTRUCTIONS

SUPPLY

AS

REQ'D

*10"

(254mm)

FINISHED WALL

FINISHED 

FLOOR

C/L OF SEAT POST HOLES
140mm (5-1/2" CENTERS)

28-7/16"

(723 mm)

14"

(355 mm)

14"

(356 mm)

9-5/16"

(236 mm)

10-3/16"

(259 mm)

12"

(305 mm)

11-15/16"
(303 mm)

18-1/2"

(470 mm)

7-3/16"

(183 mm)

3/4"

(20 mm)

3"

(77 mm)

11/16"

(18 mm)

16-1/2"

(419 mm)

28-5/8"

(727 mm)

14-7/16"

(366 mm)

Summary of Contents for LOFT 2535













Reviews: