SAFETY INFORMATION
• Read all instructions before beginning; Save these instructions for future use.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention
to this manual and stay within its guidelines when using this product.
• This controller is rated IP20; avoid the sun and moisture.
• Avoid using controller in areas where extreme hot, cold, dust, or humidity exist.
• This controller is suitable for indoor, dry locations only.
• Always be sure to store this controller in an area with proper ventilation to
avoid overheating.
These products may represent a possible shock or
fire hazard if improperly installed or attached in any
way. Products should be installed in accordance
with these instructions, current electrical codes,
and/or the current National Electric Code (NEC).
This controller is battery operated and requires
3x AAA batteries (not included).
Page 1 of 2
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
WARNING
WARNING
TRULUX
RF Tunable Remote Control
INSTALLATION INSTRUCTIONS
TWRF-3AAA
BATTERY
OPERATED
SYNCING CONTROLLER TO RECEIVER (SEE FIGURES 1 & 2):
This controller is battery operated and requires
3x AAA batteries (not included).
This controller requires a Radio Frequency receiver for
operation (REC-5A-4Z or REC-5A-4Z-WiFi sold separately).
1. Press the power button on the controller once to turn on power
to the controller.
2. Press the “Learning Key” on the receiver.
3. Select a zone by pressing one of the four zone buttons on the
controller, then touch color temperature wheel to activate controller.
4. Once successfully synced, the connected light source will blink.
5. Repeat steps 2-3 when syncing multiple receivers to a single
controller.
6. Press and hold the “Learning Key” to clear out saved sync data
when wanting to reset scenes or zones.
FIGURE 1
FIGURE 2
OPERATING CONTROLLER (SEE FIGURE 2):
This controller is battery operated and requires
3x AAA batteries (not included).
1. Press power button in center of remote for On/Off power control.
The power indicator light will turn on when remote is awake.
2. Touch and slide the color temperature wheel for cool to warm
CCT control.
3. Press and hold brightness button in center of color temperature
wheel for up/down 1-100% brightness control.
4. Press the pre-set brightness buttons for 15%, 25%, 50%, or 100%
pre-set brightness levels.
5. To select a zone, press one of the four zone buttons once. Memory
can select multiple zones simultaneously.
6. To save a scene, determine desired settings, press and hold
scene button for 2 seconds. Memory will hold 3 scenes per zone.
7. To select a scene, press one of the three scene buttons once.
CARE AND MAINTENANCE:
1. For cleaning, use a soft, dry or damp cloth. Do not use harsh chemicals or abrasives.
2. This controller is battery operated and requires 3x AAA batteries (not included). If swallowed, batteries could cause severe injury or death. Seek
medical attention immediately. Non-rechargeable batteries are not to be recharged. Remove exhausted batteries from the product; Please
dispose of batteries properly. Do not dispose of batteries in fire; Batteries may explode or leak.
Power
Indicator light
Brightness
Color Temperature
Wheel
Zones 1-4
Scenes 1-3
Pre-set 50%
Brightness
Pre-set 25%
Brightness
Power (On/Off)
Pre-set 15%
Brightness
Pre-set 100%
Brightness
SR-1009FA
LED CONTROLLER
INPUT
12-36V D
C
PRI
SEC
Learning Key
MASTER
SLAVE
CW
W
WW
B
CW
G
WW
R
° tc=75°C
150805V1
PRI:
Uin=12-36VDC
Iin=20.5A
SEC:
Uout=4x(12-36)VDC
Iout=4x5A
Pout=4x(60-180)W
TEMP RANGE:-20°C-+50°C
6-7mm
0.5-1.5mm
2
Trulux RF Receiver
(sold separately)
To 12-24V DC
Power Supply
Learning Key
RF Controller “talks” to the receiver via a
wireless Radio Frequency (RF) signal
©2019 American Lighting, Inc. REV1913 www.AmericanLighting.com
