ALDI FERREX GSR2800 User Manual Download

Page: 1 / 33

PRODUCED IN CHINA FOR:

Great care has gone into the manufacture of this product and it should

therefore provide you with years of good service when used properly. In

the event of product failure within its intended use over the course of the

first 3 years after date of purchase, we will remedy the problem as quickly

as possible once it has been brought to our attention. In the unlikely event

of such an occurrence, or if you require any information about the product,

please contact us via our helpline support services, details of which are to be

found both in this manual and on the product itself.

ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH

ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE
Visit us at www.aldi.com

AFTER SALES SUPPORT

805016

[email protected]

MODEL:

GSR2800

03/2021

+44(0) 1904727501

+353(0) 19022605

YEAR

WARRANTY

User Manual

ELECTRIC GARDEN

SHREDDER

Original User Manual

Summary of Contents for FERREX GSR2800


































Search results

Summary of Contents for FERREX GSR2800

Reviews:

Related manuals for FERREX GSR2800

Brands by name

Popular brands

ALDI FERREX GSR2800, User Manual

Search results

Summary of Contents for FERREX GSR2800

Reviews:

Related manuals for FERREX GSR2800

Brands by name

Popular brands