18” PEDESTAL FAN
18” (45,7 cm) MODEL 9418
1
Rev. B 5/08
5084034
DESCRIPTION
The Air King® 18” (45,7 cm) pedestal fan features 3-speed rotary knob
operation with a 3-paddle fan blade and variable height adjustments.
This fan has a permanently lubricated motor with a 9 ft. (2,74 m) 18/3
cord set and is constructed of sturdy, powder coated steel.
SPECIFICATIONS
Motor ...................................... 120 V, 60 Hz
Blade diameter ....................... 18” (45,7 cm)
Speeds .................................... 3
Control .................................... Rotary Switch
Air flow distribution ................ 360°
Approvals ................................ ETL Listed. Close mesh fan guard
meets OSHA requirements.
ASSEMBLY
TOOLS REQUIRED FOR ASSEMBLY
• Hex Wrench (Supplied in Parts Bag)
NOTE: ALL HARDWARE REFERRED TO IN THE INSTRUCTIONS MAY
BE FOUND IN THE SUPPLIED PARTS BAG.
1. Lay Fan Head on flat surface, so the front side is facing down. Hold Yoke
so the side with the nut is facing up. Loosely attach one Grill Knob and
one Rubber Spacer to the Head Assembly. Attach the other Grill Knob
and Rubber Spacer to the Head Assembly and FIRMLY tighten. Return
to the first Grill Knob and FIRMLY tighten.
(Figure 1)
NOTE: THE UPPER PIPE HAS 2 BUMPS, ONE AT EACH END. THE BUMP
CLOSER TO THE END OF THE PIPE INDICATES THE TOP. THIS END
FITS INTO THE YOkE.
2. Make sure Bump on Upper Pipe is aligned with formed section of Yoke.
Insert Upper Pipe into Yoke. To ensure fit is tight, twist Upper Pipe until
it is tight inside of Yoke.
(Figure 1)
NOTE: THE UPPER PIPE SHOULD FIT COMPLETELY INSIDE OF THE YOkE.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precau-
tions should always be followed to reduce the
risk of fire, electric shock and injury to person,
including the following:
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the
electrical requirements of the Fan.
3. Use this Fan only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
4. Unplug power cord before installing, servicing, or moving the Fan.
WARNING:
DO NOT DEPEND UPON THE ON-OFF
SWITCH AS THE SOLE MEANS OF DISCONNECTING
POWER WHEN INSTALLING OR SERVICING THE FAN.
ALWAYS UNPLUG THE POWER CORD.
5. This Fan must NOT be used in potentially dangerous
locations such as flammable, explosive, chemical-laden
or wet atmospheres.
6. The power cord is equipped with a three-prong grounded
plug that must be inserted into a matching receptacle. Under
no circumstances should the grounding prong be cut off the
plug. Where a two-prong wall receptacle is encountered,
it must be replaced with a properly grounded three-prong
receptacle installed in accordance with the National Electrical
Code (NEC) and all applicable local codes and ordinances.
This work must be done only by a qualified electrician, using
copper wire only.
WARNING:
DO NOT USE A THREE-PRONG ADAPTER.
IMPROPER CONNECTION MAY CREATE THE RISk OF
ELECTRIC SHOCk. USE OF SUCH ADAPTERS IS NOT
PERMITTED IN CANADA.
WARNING:
THIS PLUG IS A SAFETY FEATURE. TO
REDUCE THE RISk OF FIRE, ELECTRIC SHOCk AND
PERSONAL INjURY, DO NOT REMOVE, REPLACE,
REPAIR OR TAMPER WITH THE ORIGINALLY SUPPLIED
PLUG. IF THE FAN DOES NOT FUNCTION PROPERLY, IT
MAY BE DUE TO THE SAFETY DEVICE INCORPORATED
IN THIS PLUG.
7. Where possible, avoid the use of extension cords. If they must
be used, minimize the risk of overheating by ensuring that they
are UL listed. Never use a single extension cord to operate
more than one Fan.
8. Do not operate any Fan with a damaged cord or plug after
the Fan malfunctions, has been dropped or damaged in
any manner. Return Fan to authorized service facility for
examination, electrical or mechanical adjustment or repair.
9. Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric
shock, fire, or damage the Fan. Do not block or tamper with
the Fan in any manner while it is in operation.
10.Always place the Fan on a stable, flat, level surface when
operating, to avoid the chance of the Fan overturning. Locate
the Power Cord so the Fan or other objects are not resting on it.
Do not run Power Cord under carpeting. Do not cover Power
Cord with throw rugs, runners, or the like. Arrange Power Cord
away from room traffic and where it will not be tripped over.
11.This Fan is not intended for use in wet or damp locations.
Never locate a Fan where it may fall into a bathtub or other
water container.
12.Do not use Fan outdoors.
13.
This Fan is not suitable for use in hazardous locations. Please refer
to National Electric Code (NEC) Article 500 or applicable state
or local codes or standards relating to electrical requirements
for Hazardous locations.
THIS FAN DOES NOT MEET THE
REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING:
REDUCE THE RISk OF FIRE OR ELECTRIC
SHOCk – DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICES.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DE
-
SCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COM
-
PLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
OPERATING INSTRUCTIONS & PARTS MANUAL
SAVE THESE INSTRUCTIONS
