Installation Instructions
312-366
702-466 SynthaMax Dry Media Filter - Black
Component Identification
2012-18 JEEP Wrangler JK
V6-3.6L
For Part Numbers:
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-498-6951 to speak with
a representative in our Customer Service Center before returning the product.
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories. Write
down all memory settings before disconnecting the
negative battery cable. Some radios will require
an anti-theft code to be entered after the battery is
reconnected. The anti-theft code is typically supplied
with your owner’s manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles anti-
theft code.
TO START:
AA
Z
Y
R
W
K
U
X
X
K
U
K
K
W
J
J
V
V
K
V
K
V
U
K
K
K
R
R
J
K
J
K
J
P
J P
O
F
F
C
G
N K
M
J
Q
H
H
T
O
S
M
J
K
H
J
K
K
P
P
J
J
J
K
P
K
L
I
E
D
A
A
B
Description
Qty. Part #
A
B
C
D
E
F
G
H
I
J
K
L
M
HOSE CLAMP # 52
HOSE; 3-1/4” ID X 2”L REINFORCED
INTAKE TUBE
HOSE; 5/8”ID X 14”L
VENT; 90DEG, 5/8” HOSE, 1/4”NPT, BLACK
HOSE CLAMP #56
HOSE; 3-1/2”ID X 2-1/2”L HUMP REINFORCED
BOLT; M6 X 1.00” 12MM BUTTONHEAD,SS
ZIP TIE, 8” TREE PUSH-MNT
WASHER; M6 SPLIT LOCK ZINC
WASHER; 6MM FLAT, SS
BRACKET; 69-2521, “L”, SML, STL, TB/PC
BOLT; M6 X 1.00 X 12MM. HEXHEAD, SS
2
1
1
1
1
2
1
3
2
12
16
2
2
08610
08690
KIT27570TK
084083
08525
08620
08699
07794
1-127
1-3025
08269
070066A
07727
Description
Qty. Part #
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
BRACKET; “L”, 63-1566, STL, TB/PC
STUD; RUBBER MNT, M/F, 1/2”L X 1”W
BOLT; M6 X 1.00 X 16MM, BUTTONHEAD, SS
HEAT SHIELD LID
EDGE TRIM (35”)
BRACKET; “Z”, 63-1566, STL, TB/PC
HEAT SHIELD
NUT; 6MM NYLOCK, HEXHEAD, SS
BOLT; 6MM-1.00 X 16MM, SS
BRACKET; 69-6026, “Z”, STL, TB/PC
MOUNT, PLASTIC AIRBOX
ADAPTER; UNIVERSAL, 6” FILTER 3.5”
HOSE CLAMP # 104
AIR FILTER
1
2
5
1
1
1
1
3
4
2
2
1
1
1
083164
070228
07730
KIT312366LIDC
102471
083163
074108
07512
07812
070061A
8-186-1
21512-1
08697
702-466
2. Lift up and remove the engine cover.
3. Remove the two bolts which secure the factory intake
tube to the fan shroud. Loosen the hose clamp securing
the factory intake tube to the air filter housing. Loosen
the hose clamp securing the factory intake tube to the
throttle body.
4. Lift up the intake tube and then disconnect the inlet
air temperature electrical connection. Then remove the
intake tube from the vehicle.
5. Disconnect the crank case vent hose from the crank
case vent tube. Lift up and remove the air filter housing
from the vehicle.
NOTE: AIRAID recommends that customers do not
discard factory air intake.
6. Remove the bolt shown that secures the air box mount
bracket to the inner fender.
