Installation Instructions
302-371
702-461 SynthaMax Dry Media Filter - Black
Component Identification
2009-18 RAM 1500
2019 RAM 1500 Classic
2013-18 RAM 2500 /3500
V8-5.7L
For Part Numbers:
Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-498-6951 to speak with
a representative in our Customer Service Center before returning the product.
See Airaid.com for CARB status on each part for a specific vehicle
NOT LEGAL FOR SALE OR USE ON ANY POLLUTION
CONTROLLED MOTOR VEHICLE IN CALIFORNIA OR
STATES ADOPTING CALIFORNIA EMISSION PROCEDURES.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories. Write
down all memory settings before disconnecting the
negative battery cable. Some radios will require
an anti-theft code to be entered after the battery is
reconnected. The anti-theft code is typically supplied
with your owner’s manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles anti-
theft code.
TO START:
Description
Qty. Part #
Description
Qty. Part #
Description
Qty. Part #
A
H
D
I
E
C
AA
B
D
R
P
M
N
M
M
M
M
S
M
K
L
M
J
D
F
G
O
U
V
W
X
Q
T
R
P
AC
Y Z
Y Z
YZ
Y Z
Y
Z
YZ
AB
C
AD
AE
C
C
A
HOSE CLAMP #56
1 08620
B
HOSE; 4” TO 3-1/2” ID 90
1 99352-01
C
HOSE CLAMP
4 08413
D
HOSE CLAMP #64 STAINLESS
3 08645
E
EXTENSION HARNESS
1 21681
F
INTAKE TUBE
1 KIT27462TK
G
GROMMET; 1”OD,1/2”ID
1 08064
H
VENT; STRT, 5/8 BARBED 1/4
1 08911-1
I
HOSE; 5/8”ID X 14”L
1 5-4015
J
HOSE; 4” ID X 3” L HUMP
1 KITHUMPHS09EPDM
K
BOLT; M6 X 1.00 X 16MM
2
07730
L
WASHER; 1/4” LOCK, ZN
2
08198
M
WASHER; 1/4”ID X 5/8”OD
8
08275
N
HEAT SHIELD
1
073126
O
ADAPTOR; #454
1
27300
P
BOLT; 6MM-1.00 X 16MM
3
07812
Q
BRACKET; “Z”, STL, TK/PC
1
083103-1A
R
NUT; 6MM NYLOCK, HEX SS
3
07512
S
BRACKET; “L”, STL, TK/PC
1
083127A
T
EDGE TRIM (55”)
1
102480
U
HOSE CLAMP # 104
1
08697
V
AIR FILTER
1
702-461
W
HEAT SHIELD A
1
073127
X
HEAT SHIELD B
1
073128
Y
M5 WASHER
8
07724
Z
M5 BOLT
8
07740
AA
EXTENSION HARNESS
1
21680
AB
SPACER
1
06555
AC
BOLT; M6 X 1.00 X 20MM
1
07795
AD
CABLE TIES; 11” BLACK
1
21590
AE
VENT; 90DEG, 3/4” HOSE
1
A2128-44
2. Release the red locking tab and then disconnect the
inlet air temperature electrical connection.
3. Loosen the hose clamp which secures the intake tube
to the throttle body.
4. Disconnect the crank case vent hose from the air box.
5. Disconnect the factory intake hose from the throttle
body, then lift up the air box assembly and then remove
it from the vehicle.
NOTE: AIRAID recommends that customers do not
discard factory air intake.
6. Lift up the engine cover to dislodge it from the
mounting posts and then remove it from the vehicle.
