![background image](http://html1.mh-extra.com/html/aerogarden/aerogarden-300177aa/aerogarden-300177aa_replacement-manual_2862548001.webp)
Grow Surface
Grow Surface
Opening
Bowl
View Door
Directions for Replacing AeroGarden Pump
Installing New Pump
Removing Old Pump
Congratulations...
You have replaced your
AeroGarden Pump!
TM
300177AA
Filter
Connector
Screw
Pump
Tower
Upside Down Grow Surface:
Pump Cover Plate
Wire Slot
Filter
Metal
Contact
Unplug AeroGarden.
Remove the
Bowl
from the
Base
. Do not empty the
water.
Remove the
Grow Surface
from the
Bowl
and place on
a counter covered by a
towel (your roots will be
dripping with water).
Hint: Lift the View Door and slide
one hand into the Bowl to lift.
Don’t worry if you gently tear
some roots.
Turn the
Grow Surface
upside down on the towel,
with the back of the
Pump
Tower
facing you.
(see top
right photo)
Take out
Pump Filter
, rinse
it (no soap) and set it aside.
Remove the
Pump Connector
Screw
in the
Pump Connector
using a Phillips-head
screwdriver.
Pull up on
Pump Connector
to disconnect it from the
bottom of the
Grow Surface
.
Remove the
Pump
by inserting
the flat-head screwdriver into
the space under the pump.
Push down on the handle of the
screwdriver to lift the
Pump
out
of the
Pump Tower
.
1
2
3
5
6
Pull wire out of
Wire Slot
.
Discard old
Pump
in trash.
Remove part A with needle-nose
pliers and discard in trash.
7
10
8
11
12
Adjust
Pump Dial
to the 2 o’clock position
(2 clicks).
Replace and screw in the
Connector Screw
so it is hand-tight (no power tools, please!)
Place
Pump Filter
back into slot.
Place
Grow Surface
upright on towel and
gently replace plants back into their original
positions on the
Grow Surface
.
Place
Grow Surface
back into bowl and
replace bowl on the
Base
. Press down
firmly on the
Grow Surface
.
13
Plug the
Pump Connector
into the
Grow
Surface
so that the
Metal Contacts
face up
and out and the
Connector Wire
is inside the
Wire Slot
.
15
16
17
18
19
Insert the new
Pump
into the
Pump Tower
making sure that:
a. The rubber feet of the
Pump
are facing up.
b. The
Pump Connector Wire
goes behind
and underneath the
Pump
.
c.
Pump Cover Plate
is snapped back onto
top of
Pump
.
14
Directions continued on back
Part A
Pump
Connector
Screw
Pump
Connector
Pump
Pump
Connector
Wire
If you have any questions please feel free to contact Customer Service:
1-800-GROW-NOW (1-800-476-9669) or email: info
@
aerogrow.com
Wire Slot
Tools Needed:
•
Flat-head screwdriver
•
Phillips-head screwdriver
•
Needle-nose pliers
Gently remove each plant
from its
Grow Surface
Opening
and place the plants
upright in the
Bowl
so that
the roots are in the water.
Hint: Note where the plants were
positioned on the Grow Surface.
4
9
Remove
Pump Cover Plate
–
insert flat-head screwdriver
into each of the 3 rectangular
slots and turn screwdriver 90
to help pry out the cover plate.
It is okay to use force.
I N T E R N A T I O N A L , I N C .
©2006 AeroGrow International, Inc