AEM 21-8100 Installation Instructions Manual Download

Page: 1 / 13

Brute Force

Intake

System

Equipped with AEM DRYFLOW Filter. No oil required

Installation Instructions for:

Part Number 21-8100

1997-2003 Ford F-Series Exc. Super-Duty & Lightning 5.4L V8

1997-2004 Ford Expedition 5.4L V8

1998-1999 Lincoln Navigator 5.4L V8

ADVANCED ENGINE MANAGEMENT INC.

2205 126

Street, Unit A Hawthorne, CA. 90250

Phone: (310) 484-2322 Fax: (310) 484-0152

www.aempower.com

Instructions Part Number: 10-8100

1997-2003 Ford F-Series Exc. Super-Duty & Lightning 5.4L V8 C.A.R.B. E.O. #D-392-19

1997-2003 Ford Expedition 5.4L V8 C.A.R.B. E.O. #D-392-19

1998-1999 Lincoln Navigator 5.4L V8 C.A.R.B. E.O. #D-392-19

2004 Ford Expedition 5.4L V8 C.A.R.B. E.O. #D-392-27

Brute Force Intake Systems that are pending CARB approval are illegal in California except on racing

vehicles which may never be used on public highways.

Summary of Contents for 21-8100














Search results

Summary of Contents for 21-8100

Reviews:

Related manuals for 21-8100

Brands by name

Popular brands

AEM 21-8100, Installation Instructions Manual

Search results

Summary of Contents for 21-8100

Reviews:

Related manuals for 21-8100

Brands by name

Popular brands