![background image](http://html.mh-extra.com/html/adtran/hdsl4-t200-h4tu-r/hdsl4-t200-h4tu-r_specifications_2855122001.webp)
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
For more information, refer to the Installation and Maintenance Practice (P/N 61223HDSL4L2-5) available online at
.
HDSL4
T200 H4TU-R
P/N 1223424L2
CLEI: T1L83Z3C_ _
T200 HDSL4 Transceiver Unit, Remote-Local Powered
REM
LOC
LBK
1223424L2
LOCAL
DSL 1
DSL 2
DS1
ALM
(GRN)
(YEL)
ESF/SF
(GRN)
(YEL)
(GRN)
(YEL)
B8ZS/AMI
LLB/RLB
RX
M
O
N
TX
R
S
2
3
2
*61223
424L2-
22B*
CARD EDGE PINOUTS
PROVISIONING OPTIONS
Provisioning options are assumed from settings made at the H4TU-C.
FEATURES
TScan
The ADTRAN
®
T200 H4TU-R incorporates the TScan
™
feature. TScan allows for remote
retrieval of circuit diagnostics and performs advanced fault location. For more information about
TScan refer to the Installation and Maintenance practice.
Bad Splice Detection
The Runtime TScan bad splice detection feature is an ADTRAN proprietary non-intrusive method
for detection of anomalies (bad splices) in the copper plant. This feature non-intrusively monitors
the cable pair during runtime for the presence of bad splices, which may potentially impact service.
Poor splices in the cable are often undetected by normal testing methods. Often, these splices
present no problem for the data transmission equipment until the point at which oxidation with the
splice itself causes a rapid impedance change. Such a change in impedance may cause errors,
signal margin fluctuation, and/or a retrain of the DSL transceivers. The splice detection feature is
accessed from the Troubleshooting Screen via the craft access port.
Fast Retrain
Fast Retrain is an ADTRAN proprietary feature that minimizes downtime due to an intermittent
impairment which due to its duration cannot be bridged. When such impairments occur, the fast
retrain feature will be invoked to restore service within 5 to 7 seconds, instead of the traditional 25
to 30 second retrain duration.
NOTE: Fast-Retrain capable units must be installed on both ends of the circuit for this feature
to function properly. Also, if there is a failure, for any reason, of a fast retrain attempt
then the traditional (25-30 second) retrain will be initiated.
Pin
Designation
Description
1
CH GND
Chassis ground
5
DS1-T1
DS1 receive out tip (to customer interface)
7
H1-T
HDSL4 Loop tip (facility)
11
CH GND
Chassis ground
13
H1-R
HDSL4 Loop ring (facility)
15
DS1-R1
DS1 receive out ring (to customer interface)
17
48 VR
48 VDC Return
20
VCC
+5 VDC for protection switching
27
CH GND
Chassis ground
35
48 V
48 VDC; range ±24 to ± 56 VDC (48 VDC nominal)
41
H2-T
HDSL4 Tip (Loop 2)
47
H2-R
HDSL4 Ring (Loop 2)
49
DS1-R
DS1 transmit in ring (from customer interface)
55
DS1-T
DS1 transmit in tip (from customer interface
FRONT PANEL LED STATUS
OPTIONS
Front Panel Pushbuttons
LOC
Initiates a bidirectional loopback of the T200 H4TU-R toward the network and customer
REM
Initiates a loopback at the H4TU-C toward the customer
DS1 MONITOR JACKS
TX
DS1 signal from the DCP toward network (nonintrusive)
RX
DS1 receive from the local loop (nonintrusive)
POWER
This specific unit is intended for
Local Power Only
. If a Span Powered unit is required, refer to
P/N 1223426L2.
A local power supply is available from ADTRAN by ordering P/N 1353.DSK48V04.
COMPLIANCE
This product is intended to be installed in Restricted Access Areas only and in equipment with
a Type “B” or “E” enclosure.
This product meets all requirements of Bellcore GR-1089-CORE (Class A2), ANSI T1.418-
2002. This product is NRTL listed to the applicable UL standards.
WARNING:
Up to –200 VDC may be present on telecommunications wiring. Ensure
Chassis ground is properly connected.
DSL1/DSL2
!
!
Green
Red
Loop 1/Loop 2 synchronization achieved and signal is present
No errors currently detected, and SNR margin
≥
3 dB
Loop 1/Loop 2 synchronization not achieved, in sync with
errors, or SNR margin < 3 dB
DS1
!
!
Green
Red
DS1 signal present and no errors currently detected
No DS1 signal, or signal present with errors
ALM
"
!
!
Off
Yellow
Red
No active alarm present
Loss of DSX-1 signal from the network
Loss of DS1 signal from the customer (CPE)
ESF/SF
"
!
!
Off
Green
Yellow
Unit is provisioned for UNFRAMED data
Unit is provisioned for SF data
Unit is provisioned for ESF data
B8ZS/AMI
!
!
Green
Yellow
Unit is provisioned for AMI line code
Unit is provisioned for B8ZS line code
LLB/RLB
"
!
!
Off
Yellow
Green
No local loopbacks active
Local loopback active
Active loopback at the H4TU-C toward the customer
Code
Input
Output
Power Code
C
C
Telecommunication Code (TC)
X
X
Installation Code (IC)
A
–
61223424L2-22B
0505