ABSCO SHEDS 3060HG Assembly Instruction Manual Download

Page: 1 / 53

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION - MODEL: 3060HGK 01/07/16

We thank you for choosing an Australian made shed. For further assistance please
visit our detailed instructional video library at

Http://www.abscosheds.com.au/watch-videos

At ABSCO Industries we are always looking to be number ONE, so please let us

know what you think of our instructions. Feedback makes us better.

[email protected]

6060mm

3100mm

Absco Highlander Shed

Model: 3060HG

Page 1

CONCRETE SLAB

FRONT: 5.96m

SIDE: 3.00m

HEIGHT: 2.3m

FOR CONSTRUCTION IN
NON-CYCLONIC AREAS

WIND RATING: W33N (N2)

WHEN LAYING YOUR CONCRETE

SLAB, ENSURE THERE IS A REBATED

EDGE 25mm DEEP AROUND THE PERIMETER

CONCRETE

REBATED EDGE

CHANNEL

CONCRETE SLAB

75mm WIDE
REBATE

THIS WILL HELP
WATER EGRESS FROM
THE BASE OF THE SHED

100mm

NOTE: THIS SHED HAS PORTAL FRAMES FOR STRENGTH.

THESE FRAMES WILL NEED TO BE TRIMMED 25mm TO FIT REBATE

CAN BE LAID ON A FLAT SLAB BUT

FOR BEST WATERPROOFING

RESULTS SLAB RESULTS SEE BELOW

Summary of Contents for 3060HG






















































Search results

Summary of Contents for 3060HG

Reviews:

Related manuals for 3060HG

Brands by name

Popular brands

ABSCO SHEDS 3060HG, Assembly Instruction Manual

Search results

Summary of Contents for 3060HG

Reviews:

Related manuals for 3060HG

Brands by name

Popular brands