manualshive.com logo in svg
background image

1/12

Tel: (888) 552-6467  

             Fax: (800) 316-4515

              www.tnb.com

06/18  750.1781_Rev. H

300/600W Mini Inverter

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ THIS MANUAL AND FOLLOW ALL SAFETY INSTRUCTIONS 
THOROUGHLY BEFORE OPERATING THE  INVERTER SYSTEM

SAVE THESE INSTRUCTIONS

 

 

                                                           

1. DO NOT USE OUTDOORS.

2. All unused wires must be insulated to prevent shorting.

3. Do not mount near gas or electric heaters.

4. Do not let power supply cords touch hot surfaces.

5.

D

o not use this equipment for other than its intended use.

6. The Mini Inverter should be mounted securely and in locations and at heights where it will not be readily subjected to tampering by 

unauthorized personnel.

7. The use of accessory equipment and replacement parts not recommended by manufacturer may cause an unsafe condition and 

void the warranty.

8. The AC voltage rating of this equipment is specified on the product label. Do not connect the Mini Inverter equipment to any other 

voltage.

9. Replacement fuse is supplied.

10. The Mini Inverter uses sealed valve regulated lead acid batteries. Batteries can be punctured if not handled properly, therefore use 

caution when servicing batteries.  In the event battery acid comes in contact with eyes or skin, flush with fresh water and consult a 
physician immediately.

11. Install in accordance with the National Electrical Code and local regulations.

12. The Mini  Inverter  contains potentially hazardous voltages. Installation, maintenance  and service work should be performed by 

qualified and trained personnel.

13.

Electricians and end-users need to ensure product system compatibility before final installation.

14. Units to  be  installed only as per  configuration described in this instruction manual.        

IMPORTANT:

 

Do not exceed the total rating of the Mini Inverter. Unit is rated at maximum Watt and maximum VA, where Max.W 

= Max.VA. Total load (W) must be derated when load power factor (PF) is less than 0.9 (for maximum performance)

All Thomas & Betts inverter products receive 100% quality inspection before shipment to ensure proper and satisfactory operation.
When operated under normal conditions, Thomas & Betts inverter products will provide years of dependable service. This unit is backed 
by a 1-9 year warranty. The unit is covered by a complete 1-year warranty against defects in material or workmanship, and a 9-year pro-
rata battery warranty.

BEFORE CONTACTING TECHNICAL SUPPORT PLEASE REFER TO THE TROUBLESHOOTING GUIDE INCLUDED IN 
THIS MANUAL.

MODEL 

NUMBER

AC SPECS

EMERGENCY POWER AVAILABLE FOR LOAD

APPROX. 

WEIGHT 

30 MIN

1H

1H 30MIN

2H

4H

300

120 Vac, 60Hz

3.10 Amps

300W

240W

175W

140W

80W

70LBS.

600

120 Vac, 60Hz

6.00 Amps

600W

410W

300W

240W

125W

120LBS.

347 Vac, 60Hz

2.30 Amps

600W

410W

300W

240W

125W

120LBS.

WARRANTY

 300/600W Mini Inverter

INTERRUPTIBLE EMERGENCY LIGHTING

UNIT INVERTER INSTRUCTION MANUAL

THIS UNIT CONTAINS A 

RECHARGEABLE VALVE-REGULATED  

LEAD ACID BATTERY. PLEASE 

RECYCLE OR DISPOSE OF 

PROPERLY.

Содержание Thomas & Betts 300W

























Отзывы: