background image

 

QUICK START GUIDE

 

Page 1

 

© 2023 ABB. All rights reserved.

 

SPS 

-

48V Shelf_QSG

 

Rev. 2.0

 

 

 

SPS 

-

48V Slimline Power Shelf

 

Models: J2007003L005 

-

 alpha suffixes per Slimline Power System     

Brochure

 

No vertical spacing is required, allow a minimum 

2”,

 inch clearance at back of shelf for rectifier airflow.

 

 

 

Tools required:

 

 

 

 

 

Wire cutters and strippers

 

Torque wrench 

-

 0

-

65 in

-

lb (0

-

10 Nm)

 

Screwdrivers 

-

 Philips #1 and #2, 

Flat          small

 

Cable crimpers

 

Sockets 

-

 

5/16”,

 7/16, etc.

 

  

Step 1 

-

 Mount Shelf

 

1.

 

Reposition mounting ears as required 

-

 3 screws each. (Reverse ears for 

5” 

setback.) Torque to 10 in

-

lb. 

 

       (1.2 Nm) 

-

 Phillips screwdriver.

 

2.    Attach shelf to the frame using a minimum of four screws (two on each side) 

-

 12

-

24 (provided). Torque to 35                                

 

in

-

lb. (4 Nm) 

-

 

5/16” 

socket.

 

Step 2 

-

 Connect Chassis Ground and DC Reference (CO) Ground

 

Lug Landings: #10 double

-

hole on 5/8

-

inch center (lugs not provided)

 

Some applications may rely on frame mounting screws for chassis ground, omitting the chassis ground wire.

 

Some applications may use the Chassis Ground strap, using a single wire for both chassis ground and DC            

reference ground.

 

Minimum 10 AWG wire is recommended.

 

Torque 10

-

32 screws to 30 in

-

lb. (3.4 Nm) 

-

 

5/16” 

socket.

 

Summary of Contents for J2007003L005















Reviews: