background image

Paint Preparation System
Spray Guns

INTENDED USE: 3M–Graco spray gun systems are intended for use only by
trained and professional tradesmen, and used solely for the purpose of
spray application of liquid coating materials. They must be used only in
areas which are compatible with the material being sprayed, in strict
compliance with applicable local and national regulations.

HVLP, Compliant, and Airspray

100 psi (0.7 MPa, 7 bar) Maximum Working Air Pressure
29 psi (200 kPa, 2.0 bar) Maximum Compliant Inbound Air Pressure
(HVLP and Compliant)

U.S. Patent Pending

Table of Contents

Symbols

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Selection Charts

4

. . . . . . . . . . . . . . . . . . . . . . . . 

Typical Installation

5

. . . . . . . . . . . . . . . . . . . . . . . 

Setup

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Daily Gun Care, Flushing, and Cleaning

13

. . . 

Troubleshooting

16

. . . . . . . . . . . . . . . . . . . . . . . . 

Service

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Accessories

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

27

. . . . . . . . . . . . . . . . . . . . . . . . . 

Warranty

28

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Contact Information

28

. . . . . . . . . . . . . . . . . . . . . 

Manufactured  by

Instructions – Parts List

 

II 2 G

Important Safety Instructions

Read all warnings and instructions in this manual.
Save these instructions.

Summary of Contents for 16212





























Reviews: