background image

 

 

Service Manual

 

  Computed Radiography Scanner

 

 

Doc No.:  TM-812 

Rev:  Aug 2013 

Part No.:  CR-FPM-01-003 

 

3DISC

FireCR

Quantor

 and the 

3D Cube

 are trademarks of 

3D Imaging & Simulations Corp

, South 

Korea,  and  its  affiliates.  All  other  trademarks  are  held  by  their  respective  owners  and  are  used  in  an 
editorial fashion with no intention of infringement. The data in this publication are for illustration purposes 
only and do not necessarily represent standards or specifications, which must be met by 

3D Imaging & 

Simulations  Corp.

  All  information  contained  herein  is  intended  for  guidance  purposes  only,  and 

characteristics  of  the  products  and  services  described  in  this  publication  can  be  changed  at  any  time 
without notice. Products and services may not be available in your local area. Please contact your local 
sales representative for availability information. 

3D  Imaging  &  Simulations  Corp. 

strives to provide as 

accurate information as possible, but shall not be responsible for any typographical error. 
 

 

 

© Copyright 2013 

3D Imaging & Simulations Corp

, all rights reserved, printed, and published in South 

Korea by 

3D Imaging & Simulations Corp

.  

 

 

Summary of Contents for FireCR+









































Reviews: