background image

2GIG

®

 GC3 Security & Automation System

2GIG-SP2-GC3  |  Wireless Touch Screen

10014895 C  |  Proprietary & Confidential

Nortek Security & Control  |  5919 Sea Otter Place, Suite 100  |  Carlsbad, CA 92010  |  USA  |  800-421-1587  |  www.nortekcontrol.com

Copyright © 2018 Nortek Security & Control LLC

The Wireless Touch Screen (2GIG-SP2-GC3) is a wall-mounted, full-color, touch 
screen interface that provides many of the same easy-to-use keypad functions 
available on the Control Panel. It is designed for indoor use only and gives users 
the ability to arm and disarm the system and see the status of sensor zones.

IMPORTANT:

 This keypad does not support UL 985 installations

Box Contents

Verify that the package includes the following:

»

 

1— SP2 Wireless Touch Screen

» 

  1—AC Adapter

» 

  3—Anchorless Screws

Minimum Requirements

For successful communications, the system must meet these minimum 
requirements:

»

 

The GC3 Control Panel must be running Version 3.0.2 or higher.

»

 

If connecting with WiFi, select 2.4 GHz.

Recommended Tools

»

 

Drywall Saw (or equivalent)

»

 

Pencil

»

 

Screwdriver

»

 

Drill with 3/16” masonry bit (if mounting on masonry)

Mounting the SP2 Touch Screen to the Wall

Note:

  

As an alternative to wall mounting, the SP2 Touch Screen can also 

be set on a desktop using the 2GIG-CP-DESK Desktop Kit.

To mount the SP2 Touch Screen to the wall:

1.  Use the template included to mark the three locations for the mounting 

screws on the wall.

2.  If the power cable is going to be recessed in the wall, mark the location 

of the wire access slot and use a drywall saw to cut out the oval hole.

3.  The anchorless screws do not require pre-drilling when used in 

wallboard. If mounting on concrete, grout-filled or hollow block, brick, or 
plaster, pre-drill with a 3/16” masonry bit.

4.  Drive the three mounting screws into the wall, leaving the heads about 

1/4” out.

SP2 Touch Screen Power Connection

There is a power input jack on the rear of the SP2 Touch Screen. The barrel 
connector on the end of the power supply cable plugs into the power input jack.

POWER

SUPPLY

CABLE

POWER

INPUT

JACK

FOR SURFACE
WIRING, ROUTE

POWER SUPPLY

CABLE HERE

Connecting the SP2 Touch Screen Power

In wall-mount installations, the power cable from the power supply can be surface 
run to the SP2 Touch Screen, or recessed in the wall entering through the wire 
access slot on the back of the SP2 Touch Screen.

Surface Power Wiring

Follow these steps for surface wiring:

1.  Plug the power supply cable barrel connector into the power input jack on 

the rear of the SP2 Touch Screen.

2.  Route the power supply cable into the wire retaining trough on the rear of 

the SP2 Touch Screen.

3.  Plug the power supply into an un-switched AC outlet.

4.  Attach the SP2 Touch Screen to the wall by hanging it on the three screws.

Recessed Power Wiring

Follow these steps for recessed wiring:

1.  Route the power supply cable into the wall from the power supply’s 

location.

2.  Pull the power supply cable out through the wire access slot cut in the 

wall.

3.  Plug the power supply cable barrel connector into the power input jack 

on the rear of the SP2 Touch Screen.

4.  Plug the power supply into an un-switched AC outlet.
5.  Attach the SP2 Touch Screen to the wall by hanging it on the three 

screws.

ROUTE POWER
CABLE THROUGH

CUTOUT IN WALL

HANG TOUCH SCREEN

ON MOUNTING SCREWS

Figure 3

  

SP2 Touch Screen Recessed Power Wiring

Figure 2

  

SP2 Touch Screen Power Input Connector

POWER

BUTTON

MOUNTING

SCREWS (3)

POWER

SUPPLY

WIRELESS

TOUCH

SCREEN

Figure 1

  

SP2 Wireless Touch Screen & Accessories

Reviews: