ZyAIR G-3000 User’s Guide
Chapter 18 Firmware and Configuration File Maintenance
160
To transfer the firmware and the configuration file, follow these examples:
18.4.3 Using the FTP command from the DOS Prompt Example
1
Launch the FTP client on your computer.
2
Enter “open” and the IP address of your ZyAIR.
3
Press
[ENTER]
when prompted for a username.
4
Enter “root” and your SMT password as requested. The default is 1234.
5
Enter “bin” to set transfer mode to binary.
6
Use “put” to transfer files from the computer to the ZyAIR, e.g., put firmware.bin ras
transfers the firmware on your computer (firmware.bin) to the ZyAIR and renames it
“ras”. Similarly “put config.rom rom-0” transfers the configuration file on your computer
(config.rom) to the ZyAIR and renames it “rom-0”. Likewise “get rom-0 config.rom”
transfers the configuration file on the ZyAIR to your computer and renames it
“config.rom.” See earlier in this chapter for more information on filename conventions.
7
Enter “quit” to exit the FTP prompt.
Figure 99 FTP Session Example
More commands that you may find in third party FTP clients are listed earlier in this chapter.
18.4.4 TFTP File Upload
The ZyAIR also supports the up/downloading of the firmware and the configuration file using
TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as
well, it is not recommended.
To use TFTP, your computer must have both telnet and TFTP clients. To transfer the firmware
and the configuration file, follow the procedure shown next:
1
Use telnet from your computer to connect to the ZyAIR and log in. Because TFTP does
not have any security checks, the ZyAIR records the IP address of the telnet client and
accepts TFTP requests only from this address.
331 Enter PASS command
Password:
230 Logged in
ftp> bin
200 Type I OK
ftp> put firmware.bin ras
200 Port command okay
150 Opening data connection for STOR ras
226 File received OK
ftp: 327680 bytes sent in 1.10Seconds
297.89Kbytes/sec.
ftp> quit
Summary of Contents for ZyAIR G-3000
