manualshive.com logo in svg

ZyXEL Communications XGS1210-12, User Manual

Share
Download
ZyXEL Communications XGS1210-12 User Manual Download Page 28

Chapter 4 Web Configurator

XGS1210-12 / XGS1250-12 User’s Guide

28

The following table describes the links in the navigation panel.

4.4.1  Change Your Password

After you log in for the first time, you must enter a new password using the keyboard characters ("a – z", 
"A – Z", "0 – 9", ~!@#$%^&*()_+`–={}[]:;<>./\). The password must be 8 to 15 characters long. To change it, 
click

 Management

 to display the next screen to change your login password.

Figure 23   

Change Administrator Login Password

Table 9   Navigation Panel Links

LINK

DESCRIPTION

System

This link takes you to a screen that displays general system information, loop status, and 
individual port statistics.

Port

This link takes you to a screen to enable 

Broadcast Storm Control

 and 

Loop Detection

/

Loop 

Prevention

. You can also configure advanced settings, such as transmission speed and flow 

control on a port.

VLAN

This link takes you to a screen where you can set the PVID (Port VLAN ID) on a port and create/
modify/delete IEEE 802.1Q VLAN for the Switch.

Link Aggregation

This link takes you to screens where you can logically aggregate physical links to form one 
logical and higher-bandwidth link.

Mirroring

This link takes you to a screen where you can copy traffic from one port or ports to another port 
so that you can examine the traffic from the first port without interference.

QoS

This link takes you to a screen where you can configure port-based or IEEE 802.1p QoS. The 
Switch can put packets into the queues according to the port on which the packet is received 
or the priority tag in the packet.

IGMP Snooping

This link takes you to a screen where you can configure IGMP snooping. You must enable IGMP 
snooping to use the IPTV service. It checks the IGMP packets passing through it, picks out the 
group registration information, and configures multicasting accordingly.

Management

This link takes you to screens where you can change the system login password, perform 
firmware upgrade and configuration file maintenance as well as reset/reboot the system. You 
can also configure the IP address and subnet mask, set management VID, and enable HTTP/
HTTPS and IEEE 802.3az EEE.

Summary of Contents for XGS1210-12



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands