ZyXEL Communications MSC1000G Series, User Manual

Page: 643 / 1168

Chapter 18 Commands
Management Switch Card User’s Guide
643
18.4 Common Command Notation
The following table describes commonly used command parameter notation.
Table 345
Common Command Notation
NOTATION DESCRIPTION
[…]
The optional fields in a command are enclosed in square brackets [], for instance,
ip ping
< ip-address > [<count>]
means that the count field is optional.
|
The | symbol means “or”.
sub1
This represents subtending port 1. On the MSC’s front panel this is SFP slot 1.
sub2
This represents subtending port 2. On the MSC’s front panel this is SFP slot 2.
up1
This represents uplink port 1. On the MSC’s front panel this is Gigabit interface 3 (a Gigabit
Ethernet port/SFP slot pair).
up2
This represents uplink port 2. On the MSC’s front panel this is Gigabit interface 4 (a Gigabit
Ethernet port/SFP slot pair).
enet1 ~
enet n
This represents a Gigabit Ethernet port where
n
varies depending on the number of Gigabit
Ethernet ports. On the MSC’s front panel, this is a Gigabit interface (a Gigabit Ethernet port/
SFP slot pair).
etype
: Ethernet type in hexadecimal.
t1
This is the trunk group name.
giga-port
This represents the Gigabit Ethernet uplink port(s) or subtending port(s) or both. Choose
sub1
|
sub2
|
up1
|
up2
or
enet1 ~ enet n
if trunking is disabled,
tsub
|
tup
if trunking is
enabled.
index
This is an integer that sets the index number of a table entry. The range starts at 1. The end
of the range varies by command.
ip-address
This represents a valid IP address. An IP version four address should be in dotted decimal
notation. An IPv6 address and prefix should be in colon hexadecimal notation. 192.168.1.1
is an example of an IPv4 address.
This is an example IPv6 address: 2001:0db8:1a2b:0015:0000:0000:1a2f:0000.
IPv6 addresses can be abbreviated in two ways:
Leading zeros in a block can be omitted. So 2001:0db8:1a2b:0015:0000:0000:1a2f:0000
can be written as 2001:db8:1a2b:15:0:0:1a2f:0.
Any number of consecutive blocks of zeros can be replaced by a double colon. A double
colon can only appear once in an IPv6 address. So
2001:0db8:0000:0000:1a2f:0000:0000:0015 can be written as
2001:0db8::1a2f:0000:0000:0015, 2001:0db8:0000:0000:1a2f::0015,
2001:db8::1a2f:0:0:15 or 2001:db8:0:0:1a2f::15.
mac
This represents a MAC address in "a0:c5:12:34:56:78" format.
mux
The encapsulation method. Choose either
llc
or
vcmux
.
mg-name
The media gateway name. Set this using
profile voip h248
.
netmask
This represents the bit number of the subnet mask of an IP address. The range is 0 to 32.
To find the bit number, convert the subnet mask to binary and add all of the 1’s together.
Take “255.255.255.0” for example. 255 converts to eight 1’s in binary. There are three
255’s, so add three eights together and you get the bit number (24).
port
This represents the UDP or TCP port number of a service.
priority
The VLAN priority setting (0~7).
slot
This represents the number of an individual chassis slot where a line card is located.