manualshive.com logo in svg

ZyXEL Communications GS1200 SERIES, User Manual, Page: 62 / 85

Share
Download
ZyXEL Communications GS1200 SERIES User Manual Download Page 62

Chapter 13 IGMP Snooping

GS1200 Series User’s Guide

62

Figure 46   

IGMP Snooping

The following table describes the labels in this screen.

Table 15   IGMP Snooping

LABEL

DESCRIPTION

IGMP Snooping

Enable IGMP 
Snooping

Select this option to enable IGMP Snooping to forward group multicast traffic only to ports that 
are members of that group.

Unknown 
Multicast Drop

Select this option to discard the frame when the Switch receives an unknown multicast frame. 
Otherwise, the Switch sends the frame to all ports.

IGMP Static 
Router Port

The Switch treats an IGMP query port as being connected to an IGMP multicast router (or 
server). The Switch forwards IGMP join or leave packets to an IGMP query port.

Select a port to be used as an IGMP query port.

Or, select 

Auto

 to allow any port to be used as an IGMP router port after receiving an IGMP 

query.

Note: If link aggregation is enabled, the ports in a link aggregation group will not be 

available in this field.

Apply

Click 

Apply

 to save your changes to the Switch.

Summary of Contents for GS1200 SERIES






















































































Reviews:

No comments