manualshive.com logo in svg

ZyXEL Communications GS-2724, User Manual

The ZyXEL Communications GS-2724 is a powerful networking switch designed for enterprise use. Unlock the full potential of this device by accessing the comprehensive User Manual available for free download at manualshive.com. This manual provides step-by-step instructions and valuable insights to optimize your networking setup.

Share
Download
background image

GS-2724 User’s Guide

221

C

H A P T E R

 

 35 

ARP Table

This chapter introduces ARP Table.

35.1  ARP Table Overview 

Address Resolution Protocol (ARP) is a protocol for mapping an Internet Protocol address (IP 
address) to a physical machine address, also known as a Media Access Control or MAC 
address, on the local area network. 
An IP (version 4) address is 32 bits long. In an Ethernet LAN, MAC addresses are 48 bits 
long. The ARP Table maintains an association between each MAC address and its 
corresponding IP address. 

35.1.1  How ARP Works

When an incoming packet destined for a host device on a local area network arrives at the 
Switch, the Switch's ARP program looks in the ARP Table and, if it finds the address, sends it 
to the device.
If no entry is found for the IP address, ARP broadcasts the request to all the devices on the 
LAN. The Switch fills in its own MAC and IP address in the sender address fields, and puts 
the known IP address of the target in the target IP address field. In addition, the Switch puts all 
ones in the target MAC field (FF.FF.FF.FF.FF.FF is the Ethernet broadcast address). The 
replying device (which is either the IP address of the device being sought or the router that 
knows the way) replaces the broadcast address with the target's MAC address, swaps the 
sender and target pairs, and unicasts the answer directly back to the requesting machine. ARP 
updates the ARP Table for future reference and then sends the packet to the MAC address that 
replied. 

35.2  Viewing the ARP Table   

Click 

Management 

>

 ARP Table

 in the navigation panel to open the following screen. Use 

the ARP table to view IP-to-MAC address mapping(s).

Summary of Contents for GS-2724





























































































































































































































































































































































Reviews:

No comments

Related manuals for GS-2724

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
AT&T Nighthawk M6 Pro Let'S Get Started preview
Nighthawk M6 Pro
Brand: AT&T Pages: 2
APM AQ-500h Specification Sheet preview
AQ-500h
Brand: APM Pages: 3
Patton electronics 3040/V35 Installation And Operation Manual preview
3040/V35
Brand: Patton electronics Pages: 23
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
Zhone ETHX-2214-DS3 Installation Instructions Manual preview
ETHX-2214-DS3
Brand: Zhone Pages: 28
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
MICRADIGITAL F5D7630uk4A-E Speci?Cations preview
F5D7630uk4A-E
Brand: MICRADIGITAL Pages: 2
Billion BIPAC 7100G Quick Start Manual preview
BIPAC 7100G
Brand: Billion Pages: 14
3Com Router 3000 Series Manual preview
Router 3000 Series
Brand: 3Com Pages: 37
Accusys ACD-76300 Quick Installation Manual preview
ACD-76300
Brand: Accusys Pages: 12
Cisco 1941-DC-A - MWR Mobile Wireless Edge Router Hardware Installation Manual preview
1941-DC-A - MWR Mobile Wireless Edge Router
Brand: Cisco Pages: 80
Cisco 1760 - VPN Bundle Router Quick Start Manual preview
1760 - VPN Bundle Router
Brand: Cisco Pages: 40
Cisco 1841 - 3G Bundle Router User Manual preview
1841 - 3G Bundle Router
Brand: Cisco Pages: 28
Cisco 1921-SEC/K9 Datasheet preview
1921-SEC/K9
Brand: Cisco Pages: 10
Cisco 2600-DC Series Datasheet preview
2600-DC Series
Brand: Cisco Pages: 20

Brands by name

Popular brands

Load more brands