manualshive.com logo in svg

ZyXEL Communications EX3510-B1, User Manual

Share
Download
ZyXEL Communications EX3510-B1 User Manual Download Page 272

Chapter 36 Diagnostic

EX3510-B1 User’s Guide

272

36.4  802.1ag (CFM)

Click 

Maintenance > Diagnostic

 > 

802.1ag

 to open the following screen. Use this screen to configure 

and perform Connectivity Fault Management (CFM) actions as defined by the IEEE 802.1ag standard. 
CFM protocols include Continuity Check Protocol (CCP), Link Trace (LT), and Loopback (LB).

Figure 179   

Maintenance > Diagnostic > 802.1ag

The following table describes the fields in this screen.

Table 122   Maintenance > Diagnostic > 802.1ag

LABEL

DESCRIPTION

802.1ag Connectivity Fault Management

IEEE 802.1ag 
CFM

Click this switch to enable or disable the IEEE 802.1ag CFM specification, which allows network 
administrators to identify and manage connection faults. When the switch goes to the right 

, the function is enabled. Otherwise, it is not.

Y.1731

Click this switch to enable or disable Y.1731, which monitors Ethernet performance. When the 
switch goes to the right 

, the function is enabled. Otherwise, it is not.

Interface

Select the interface on which you want to enable the IEEE 802.1ag CFM.

Summary of Contents for EX3510-B1


























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands