manualshive.com logo in svg

ZyXEL Communications EX3510-B1, User Manual

Share
Download
ZyXEL Communications EX3510-B1 User Manual Download Page 263

EX3510-B1 User’s Guide

263

C

HAPTER

 34

Firmware Upgrade

34.1  Firmware Upgrade Overview

This screen lets you upload new firmware to your Zyxel Device. You can download new firmware 
releases from your nearest Zyxel FTP site (or www.zyxel.com) to upgrade your device’s performance.

Only use firmware for your device’s specific model. Refer to the label on 

the bottom of your Zyxel Device.

34.2  Firmware Upgrade Settings

Click 

Maintenance > Firmware Upgrade 

to open the following

 

screen. Download the latest firmware file 

from the Zyxel website and upload it to your Zyxel Device using this screen. The upload process uses HTTP 
(Hypertext Transfer Protocol) and may take up to two minutes. After a successful upload, the Zyxel 
Device will reboot.

Do NOT turn off the Zyxel Device while firmware upload is in progress!

Figure 169   

Maintenance > Firmware Upgrade

The following table describes the labels in this screen. After you see the firmware updating screen, wait 
two minutes before logging into the Zyxel Device again.

Table 119   Maintenance > Firmware Upgrade

LABEL

DESCRIPTION

Upgrade Firmware

Restore Default 
Settings After 
Firmware 
Upgrade

Select the check box to have the Zyxel Device automatically reset itself after the new firmware 
is uploaded.

Summary of Contents for EX3510-B1


























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands