manualshive.com logo in svg

ZyXEL Communications ADSL2+ 4-port Gateway P-660H-D Series, User Manual

Share
Download
ZyXEL Communications ADSL2+ 4-port Gateway P-660H-D Series User Manual Download Page 60

P-660R-T Series User’s Guide

Chapter 5 LAN Setup

60

5.4  LAN TCP/IP 

The Prestige has built-in DHCP server capability that assigns IP addresses and DNS servers to 
systems that support DHCP client capability.

5.4.1  Factory LAN Defaults

The LAN parameters of the Prestige are preset in the factory with the following values:

• IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits)
• DHCP server enabled with 32 client IP addresses starting from 192.168.1.33. 

These parameters should work for the majority of installations. If your ISP gives you explicit 
DNS server address(es), read the embedded web configurator help regarding what fields need 
to be configured.

5.4.2  IP Address and Subnet Mask

Refer to 

Section 3.2 on page 46

 

in 

Chapter 3 on page 44

 for this information.

5.4.3  RIP Setup

RIP (Routing Information Protocol) allows a router to exchange routing information with 
other routers.  The 

RIP Direction

 field controls the sending and receiving of RIP packets.  

When set to:

•

Both

 -

 the Prestige will broadcast its routing table periodically and incorporate the RIP 

information that it receives.

•

In Only

 - 

the Prestige will not send any RIP packets but will accept all RIP packets 

received.

•

Out Only

 - 

the Prestige will send out RIP packets but will not accept any RIP packets 

received.

•

None

 -

 the Prestige will not send any RIP packets and will ignore any RIP packets 

received.

The 

Version

 field controls the format and the broadcasting method of the RIP packets that the 

Prestige sends (it recognizes both formats when receiving).  

RIP-1

 is universally supported; 

but RIP-2 carries more information.  RIP-1 is probably adequate for most networks, unless 
you have an unusual network topology.

Both 

RIP-2B

 and 

RIP-2M

 sends the routing data in RIP-2 format; the difference being that 

RIP-2B

 uses subnet broadcasting while 

RIP-2M

 uses multicasting.

Summary of Contents for ADSL2+ 4-port Gateway P-660H-D Series















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands