Zultys MX250 Hardware Manual Download Page 57

Page: 57 / 62

A p p e n d i x C

Regulatory and Safety Compliance

C.1

Usage

The MX250 complies with the following agency approvals and standards. The MX250 is therefore

approved for business use and connection to the PSTN in the following countries:

•

Argentina

•

Australia

•

Canada

•

China

•

Europe

•

Hong Kong

•

Japan

•

Korea

•

Mexico

•

New Zealand

•

South Africa

•

USA

C.2

Safety

•

CSA-C22.2 60950 Safety of Information Technology Equipment

•

AS/NZ 60950:2000 Safety of Information Technology Equipment

•

UL60950: Safety of Information Technology Equipment

•

IEC60950: Safety of Information Technology Equipment

C.3

Electromagnetic Compatibility (EMC) Emissions

•

FCC part 15 Class A

•

ICES-003 Radiated and Conducted Emission from digital apparatus Class A

Summary of Contents for MX250































































Search results

Summary of Contents for MX250

Reviews:

Related manuals for MX250

Brands by name

Popular brands

Zultys MX250, Hardware Manual

Search results

Summary of Contents for MX250

Reviews:

Related manuals for MX250

Brands by name

Popular brands