Warning!
- Any work on the mains power supply must only be completed by trained specialists.
- The product must be installed in accordance with country-specific
installation guidelines/standards.
- Disconnect the 230-volt power supply before
starting the installation process!
- As a precautionary measure, the power supply of the light should always be fitted with a (250VAC, 10A)
type C fuse in accordance with EN60898-1.
- The device must be fitted with an earthed conductor (earth).
- Only change the light bulb/touch the housing once
the light has cooled down.
- Only operate the device with the specific lamps intended for that purpose.
- Faulty lamps can cause a short-circuit
thereby permanently damaging the device.
- Any faulty devices should be disconnected from the power supply.
-
The light is not suitable for installation on easily flammable
surfaces.
- Installation in internal spaces is permitted as long as there is no risk of
overheating.
- Any broken protection glass must be replaced immediately.
Care and maintenance
Before any cleaning and maintenance work is completed on the light,
it must first be left to cool and the fuse for the relevant
power supply must be switched off.
For electrical safety purposes, the light must not be cleaned with water
or any other liquids and must not be submerged in water.
Therefore, only use a dry, lint-free cloth when cleaning.
Phase/outer conductor (L): brown;
Neutral/neutral conductor (N): blue;
Earth: green/yellow
Switching output/switched phase/outer
conductor (L') red and white; for parallel
bypass (continuous light) or for additional
loads. We recommend switching a maximum
of two flood lights in parallel. If the switching
capacity is higher, the additional load can be
switched via an external relay.
Sensor light Pro 19W/35W LED, 120W/400W Page 1/2
1
2
3
4
5
Turn the head of the light (1) by 180° into the
service position. Loosen the screw (2) at the
bottom of the device so that the cover (3) can be
pushed down. Then engage the lug on the
device with the middle screw (4) and attach the
device with the two remaining screws (5). Once
the installation is complete, turn the head back
into the operational position.
To ensure the operational reliability, install the
device in an area that is protected from the
elements. Maintain a safety distance of 20 cm
to ceilings (30 cm if installed in an internal
corner) and 1 m to illuminated objects. Avoid
heat sources in the immediate coverage area
as well as under the detector.
Installati
on
Power supply
Alignment
Settings
6
Installation
site
Specifications:
Nominal voltage: 220 to 240V, 50Hz
Light output: in accordance with the type of
lamp
Coverage area: 200°/140° according to the
model
Range: 12 m ahead
Twilight controller: 5 to 1000 lux
Time controller: 3 seconds to 30 minutes
Protection class: IP55, class I
Ambient temperature: -20°C to +40°C
Pro 19W LED 200
8 x high-power
LEDs
Pro 35W LED 200
15 x high-power
LEDs
Pro 120W 200
Pro 120W 140
Use a clean cloth to touch the
halogen bulb. Otherwise finger
prints and grease residues will
burn in and reduce the service life
of the lamp.
Approx. 5 lux (night) to
1000 lux (day)
Follow-up time
approx. 3 seconds to
30 minutes
Frontal detection
NOT SENSITIVE
Distance approx. -50%
Tangential detection
=
SENSITIVE
The range is dependent on the installation location and the
direction of movement. As the motion detector reacts to the
temperature fluctuations between the heat source and ambient
temperature, the range can vary depending on the installation
location.
Coverage area
Pro 400W 200
Pro 400W 140
The head of the light can now be adjusted
horizontally and vertically by approx. +/-10°. Ensure
that the halogen bulb only deviates from the
horizontal axis by a max. of 4° otherwise this will
cause a one-sided accumulation of heat. The device
cannot be operated while in the service position.
