Zte ZXR10 T1200 User Manual Download Page 76 | Manualshive

Page: 76 / 83

background image

ZXR10 T600/T1200 User Manual (IPv6 Volume)

in the NAT server, which maintains a mapping table between IPv4
and IPv6 addresses.

On the contrary, if an internal IPv6 host communicates with an
external IPv4 host, IPv6 host is mapped into an internal address
while the IPv4 host a global address. NAT technology is a solution
to interconnection between IPv4 hosts and IPv6 host.

Technically, transition from the existing network to the IPv6 net-
work is mature and step by step. The International Organization
for Standardization (ISO) and many R&D institutions have devel-
oped multiple translation mechanisms for intercommunication be-
tween IPv4 and IPv6.

The following are popular standards for

IPv4/IPv6 intercommunication translation technology:

�

6to4: RFC3056

�

Network Address Translation-Protocol Translation (NAT-PT):
RFC 2766

�

IP/ICMP TranslationStateless (SIIT): RFC 2765

�

Tunnel broker: RFC 3053

�

6over4: RFC 2529

�

SOCKS-gateway: RFC 3089

�

TCP/UDP-relay: RFC 3142

�

Dual Stack Transition Mechanism (DSTM): draft-ietf-ngtrans-
dstm-08.txt

�

Intra-Site Automatic Tunnel Addressing Protocol (ISATAP):
draft-ietf-ngtrans-isatap-08.txt

Configuring IPv6 Tunnel

To configure basic Ipv6 tunnel, perform the following steps.

St-
ep

Command

Function

1

ZXR10(config)#

interface tunnel

<

tunnel-id

>

This creates a tunnel and
enables us to enter tunnel
configuration mode.

2

ZXR10(config-if)#

tunnel mode

{

gre ip

|

mpls

traffic-eng

|

ipv6ip

[

6to4

]|

ipipv6

}

This configures tunnel mode
for IPv6 tunnel.

Result:

The basic IPv6 tunnel has been configured.

68

Confidential and Proprietary Information of ZTE CORPORATION

«
...
74
75
76
77
78
...
»

Summary of Contents for ZXR10 T1200




















































































Reviews:

No comments

Related manuals for ZXR10 T1200

Network Space MAX

Brand: LaCie Pages: 2

Brand: Tripp Lite Pages: 20

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

Brand: Xantech Pages: 6

HomePNA PCI Adapter

Brand: City-Netek Pages: 18

Total Access 1500 Dual FXS/DPO

Brand: ADTRAN Pages: 2

Brand: ActiveEye Pages: 35

Brand: Tripp Lite Pages: 3

Brand: Planet Pages: 16

Brand: Vivotek Pages: 46

JetNet 5720G-8P Series

Brand: Korenix Pages: 52

Brand: Alloy Pages: 13

Brand: Billion Pages: 2

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

Brand: ADTRAN Pages: 162

Brand: Crestron Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands