manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Figure 7-1 OSPFv3 Configuration Example

Configuration Thought

1.

Enable the IPv6 protocol on the direct connection interfaces of S1 and S2, configure

IPv6 addresses for the direct connection interfaces, configure loopback interfaces,

enable IPv6 on the loopback interfaces, and configure IPv6 addresses for the loopback

interfaces.

2.

Configure OSPFv3.

3.

Add the interfaces to OSPF area 0.

4.

Check and verify the configuration results:

Neighbors are correctly established

between the two routers, each router can learn the routes advertised by the peer

router, and each router can ping the peer loopback interface.

Configuration Commands

S1 configuration:

S1(config)#interface vlan10

S1(config-if-vlan10)#ipv6 enable

S1(config-if-vlan10)#ipv6 address 3611::11/64

S1(config-if-vlan10)#exit

S1(config)#interface loopback5

S1(config-if-loopback5)#ipv6 enable

S1(config-if-loopback5)#ipv6 address 3555::52/64

S1(config-if-loopback5)#exit

S1(config)#ipv6 router ospf 1

S1(config-ospfv3-1)#router-id 11.11.11.11

S1(config-ospfv3-1)#interface vlan10

area 0

S1(config-ospfv3-1-if-vlan10)#exit

S1(config-ospfv3)#interface loopback5 area 0

S1(config-ospfv3-1-if-loopback5)#exit

S1(config-ospfv3-1)#exit

S2 configuration:

S2(config)#interface vlan10

S2(config-if-vlan10)#ipv6 enable

S2(config-if-vlan10)#ipv6 address

3611::10/64

S2(config-if-vlan10)#exit

S2(config)#interface loopback5

S2(config-if-loopback5)#ipv6 enable

S2(config-if-loopback5)#ipv6 address

3550::52/64

7-14

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

GE MDS 4710M Setup Manual preview
MDS 4710M
Brand: GE Pages: 6
PaloAlto Networks PA-5400 Series Quick Start Manual preview
PA-5400 Series
Brand: PaloAlto Networks Pages: 2
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne Hotwire 7995 Installation Instructions Manual preview
Hotwire 7995
Brand: Paradyne Pages: 32
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Paradyne FrameSaver 9783 Installation Instructions Manual preview
FrameSaver 9783
Brand: Paradyne Pages: 28
Paradyne COMSPHERE 6800 Series Installation And Enabling/Disabling Instructions preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 7
TP-Link VIGI NVR1008 Quick Installation Manual preview
VIGI NVR1008
Brand: TP-Link Pages: 2
SyChip WLAN6065SD User Manual preview
WLAN6065SD
Brand: SyChip Pages: 24
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Brand: National Instruments Pages: 130
Network Critical SmartNA-X User Manual preview
SmartNA-X
Brand: Network Critical Pages: 200
ADTRAN 1700601G2 Quick Start Manual preview
1700601G2
Brand: ADTRAN Pages: 4
Atlantis Land Edge-Core A07-ES4548C Specification Sheet preview
Edge-Core A07-ES4548C
Brand: Atlantis Land Pages: 2
QNAP TS 73A Series User Manual preview
TS 73A Series
Brand: QNAP Pages: 68
Paradyne JetFusion 2004 User Manual preview
JetFusion 2004
Brand: Paradyne Pages: 216
Verizon VZ4010 User Manual preview
VZ4010
Brand: Verizon Pages: 39

Brands by name

Popular brands

Load more brands