Zte ZXR10 2900E Series Command Reference Manual Download Page 128

Page: 128 / 750

ZXR10 2900E Series Command Reference

Command Mode

Global configuration mode

Syntax

show poe device

Example

The following example shows POE status of the switch:

zte(cfg)#show poe device

PSE firmware version

: ZTE 3.3

PSE max power configed

250 watt

PSE power threshold

: 15 watt

PSE max power

: 250 watt

PSE current power

: 0 watt

PSE average-power

: 0 watt

PSE peak-power

: 0 watt

4.3.9 show poe status

Purpose

This command shows POE status of ports.

Command Mode

Global configuration mode

Syntax

show poe status

[

port

portlist

Parameter Description

Parameter

Description

portlist

Port list. The command without the

portlist

parameter shows

POE status of all ports.

Example

The following example shows the POE status of ports 1 and 2:

zte(cfg)#show poe status port 1/1-2

port: 1/1

power up

: off

power device

: searching

power device type

: not power device

4-68

SJ-20130731155059-003|2013-11-27 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 2900E Series















































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZXR10 2900E Series

Reviews:

Zte ZXR10 2900E Series, Command Reference Manual, Page: 128 / 750

Search results

Summary of Contents for ZXR10 2900E Series

Reviews: