Zte ZXR10 2900E Series Command Reference Manual Download Page 542

Page: 542 / 750

ZXR10 2900E Series Command Reference

4.29.9 set zesr link-hello hello-interval

Purpose

This command sets the interval of sending link-hello packets and time-out period of

link-hello packets.

Command Mode

Global configuration mode

Syntax

set zesr link-hello hello-interval

10-10000

fail-times

3-10

Parameter Description

Parameter

Description

10-10000

Interval of sending link-hello packets, default: 1000 ms.

3-10

Time-out period of link-hello packets, default: 5.

Example

The following example sets the interval of sending link-hello packets on port 1/1:

zte(cfg)#set zesr link-hello hello-interval 10 fail-times 5

4.29.10 set zesr protocol-mac

Purpose

This command sets the mode of destination MAC addresses in protocol packets.

Command Mode

Global configuration mode

Syntax

set zesr protocol-mac

{

normal

special

}

Parameter Description

Parameter

Description

normal

MAC address mode defined in RFC 3619.

special

MAC address mode defined by ZTE.

4-482

SJ-20130731155059-003|2013-11-27 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 2900E Series















































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ZXR10 2900E Series

Reviews:

Zte ZXR10 2900E Series, Command Reference Manual, Page: 542 / 750

Search results

Summary of Contents for ZXR10 2900E Series

Reviews: