manualshive.com logo in svg

Zte ZXR10 2900E Series, Command Reference Manual, Page: 173 / 750

Share
Download
Zte ZXR10 2900E Series Command Reference Manual Download Page 173

Chapter 4 Service Configuration

Syntax

set mac learning except session

<

1-100

>{

clear

|

mac-address

<

HH.HH.HH.HH.HH.HH

>

ma

c-mask

<

HH.HH.HH.HH.HH.HH

>[

vlan

<

1-4094

>]}

Parameter Description

Parameter

Description

session

Session ID. One session is configured with one MAC address

segment.

<

1-100

>

Up to 100 sessions are supported.

clear

Clears the session configuration.

mac-address

MAC address that is not learned.

<

HH.HH.HH.HH.HH.HH

>

MAC address.

mac-mask

MAC address mask.

<

HH.HH.HH.HH.HH.HH

>

Mask value.

vlan

Sets the function of not learn specific MAC addresses on the

VLAN.

<

1-4094

>

VLAN ID

Guidelines

After a session is bound with a port/trunk, the session does not learn the matched MAC

addresses, but forwards them.

4.7.36 set mac learning except session unbind

Purpose

This command removes the binding relationship between ports/trunks and all sessions.

Command Mode

Global configuration modes

Syntax

set mac learning except

{

port

<

portlist

>|

trunk

<

trunklist

>}

session unbind

Parameter Description

Parameter

Description

port

Ports bound with sessions.

4-113

SJ-20130731155059-003|2013-11-27 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 2900E Series















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments