Zte ZXMW NR8250 Manual Download Page 83

Page: 83 / 124

Chapter 2 Alarm

Possible Causes

The BPDU packet is received at the edge port on which the BPDU Guard function is

enabled.

Handling Procedure

Check whether the edge port is connected with the user terminal.

If yes, go to step 2.

If no, modify the port as a non-edge port.

Find out the source of the BPDU packet and check whether network attack occurs. If

yes, contact the network engineer.

2.4.2 134243760 MSTP port LOOP Guard

Alarm Property

Alarm Code: 134243760

Alarm Information: The alarm is reported if the port is blocked due to the LOOP Guard

function.

Alarm Level: Major

Alarm Type: Environment Alarm

Sub-code Description

None

Effect on the System

The port is blocked for some time.

Possible Causes

The port configured with LOOP Guard function does not receive the BPDU packet for a

long time.

Handling Procedure

Check whether the port should be configured with LOOP Guard function, whether the link

is congested, whether there are unidirectional link problems, and whether the port receives

and sends BPDU packets properly.

Check whether the port configured with LOOP Guard function is a root port, standby

port, or alternate port.

If yes, go to step 2.

If no, cancel the Loop Guard configuration.

Check whether the link is congested or there are unidirectional link problems. If yes,

contact the network engineer.

2-69

SJ-20111008094748-008|2012–05–30 (R1.1)

ZTE Proprietary and Confidential

Summary of Contents for ZXMW NR8250





























































































































Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands

Zte ZXMW NR8250, Manual

Search results

Summary of Contents for ZXMW NR8250

Reviews:

Related manuals for ZXMW NR8250

Brands by name

Popular brands