Zte ZXA10 C300 Configuration Manual Download Page 107

Page: 107 / 301

Chapter 8 ACL Configuration

Note:

The hybrid ACL number ranges from 300 to 399. A hybrid ACL is applied to the

Ethernet interface and PON-ONU interface.

Configure the ACL rules.

ZXAN(config-hybd-acl)#rule 1 deny any any any arp

ZXAN(config-hybd-acl)#rule 2 deny any any 192.168.1.0 0.0.0.255 ip ingress 0000.

0000.0001 0000.0000.0000 egress any

ZXAN(config-hybd-acl)#rule 3 permit any any any any

ZXAN(config-hybd-acl)#exit

Note:

Each hybrid ACL supports up to 127 rules.

If the time range is not configured, the rule is always effective.

In Ethernet interface configuration mode, apply the ACL.

ZXAN(config)#interface gei_1/21/1

ZXAN(config-if)#ip access-group 300 in

(Optional) Query the ACL configuration.

ZXAN(config-if)#show acl 300

acl hybrid number 300

rule 1 deny any any any arp ingress any egress any

rule 2 deny any any 192.168.1.0 0.0.0.255

ip ingress 0000.0000.0001 0000.0000.0000 egress any

rule 3 permit any any any any ingress any egress any

(Optional) Query the interface bound with the ACL.

ZXAN(config-if)#show access-list bound

Interface

Direction Type

Status

Acl number/name

gei_1/21/1

V4HYBD successful

300

– End of Steps –

8.5 Configuring an IPv6 Hybrid ACL

This section describes how to configure an IPv6 hybrid ACL and apply it to an Ethernet

interface.

8-7

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands