ZOTYE JNJ7155 Quick Start Manual Download Page 54

Page: 54 / 290

052

Combination instrument

Fuel gauge

LCD of instrument

Caution !

● Before refueling, turn start switch to OFF.

● The fuel shall be above 1/4 volume as possible.

● When running on a slope or rough road, the warning light

illumination may be abnormal.

Description!

The leftward triangle symbol in the icon

on the fuel meter

indicates that the fuel filler cap is on the left of vehicle body.

Current vehicle speed

It displays current vehicle speed.

Average fuel

consumption

Instant fuel

consumption

Average vehicle

speed

Driving
mileage

Summary of Contents for JNJ7155



































































































































































































































































































Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands

ZOTYE JNJ7155, Quick Start Manual

Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands